All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled, round, steel tubing. Two external loads are exerted at the edge of lower part of member BF and CE with magnitudes of 10kN and 15KN, respectively. The loads are placed in a vertical position abiding gravitational direction. Analyze the truss structures based on the instruction listed. (i) loading known as a zero-force member. Figure out the member(s) with solid justification. Among all rods of the truss shown in the figure, there is a member that supports no (ii) direction for each support reaction. The truss is supported with two surface forces as shown. Determine the magnitude and

All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled, round, steel tubing. Two external loads are exerted at the edge of lower part of member BF and CE with magnitudes of 10kN and 15KN, respectively. The loads are placed in a vertical position abiding gravitational direction. Analyze the truss structures based on the instruction listed. (i) loading known as a zero-force member. Figure out the member(s) with solid justification. Among all rods of the truss shown in the figure, there is a member that supports no (ii) direction for each support reaction. The truss is supported with two surface forces as shown. Determine the magnitude and

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dari gambar di atas gambarlah diagram bebas untuk semua batang.Kemudian carilah gaya reaksi tumpuan pada titik A dan G , serta gaya padatitik-titik sambungan semua batang(Cari dulu gaya reaksi pada tumpuannya, lalu gaya pada titik-tiksambungannya)
B8
مطلوب Medical Instrumentation /1 The stages of operation of autoclaves include air removal, steam admission and sterilization cycle Includes heating up, holding/exposure, and cooling stages. O Includes cooling, holding/exposure, and heating up stages. O Includes holding/exposure, heating up, and cooling stages. O None of them O The paraffin waxes miss the heat slowly
Is this true or false? thank you
Is the effect of temperature on all materials the same? Yes or no.
What percentage of microorganisms survive following treatment if the population is reduced by a 7 log reduction? %
In foundry work, a riser is which one of the following: a. vertical channel into which molten metal is poured into the mold b. choking mechanism at the bottom into the mold C. foundryman who moves the molten metal to the mold d. reservoirs of molten metal to supply any molten metal to prevent porosity е. channel in the mold leading from the downsprue to the main mold cavity
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…
Why is the feeder used in the casting process? What is its significance and how should it be designed? In shapeinterpret by drawing.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
1,000,000 mm = ? m 2. 1,000,000 µg = ?g 3. 1,000,000 mg =?g 4. 1,000,000 cm =? m 5. 1,000,000 mL = ?L 6. 1,000,000 um = ? cm 7. 1,000,000 mm = ? km 8. 1,000,000 cm = ? km 9. 1,000,000 mg = ? kg 10. .1,000,000 g = ? mg 11. 1,000,000 km = ? m 12. 1,000,000 kg =2g 1. 13. 1,000,000 km = ? cm 14. 1,000,000 mL = ? L 15. 1,000,000 kg =? mg 16. 1,000,000 cg =?g 17. 50 mi = ? in PART A-3 18. 42 °F = ? °C 19. 73 °F = ?° C 20. 12 °C = ? °F 21. 70 °C = ? °F 22. 25 °C = ? K 23. 300 °K = ? °C 24. 100 ft/sec =? mi/hr 25. 100 mi / hr = ? ft / sec. 26..5 gal / min = ? gal/hr 27. 5 pints / min = ? gal / hr 28. 3 g/cm3 = ? kg/m3 29. 180 kg / m3 =? g/ mm3 30. 200 lb/in2 = ? tons/ft2 31. 2.5 tons / ft2 = ? lb / in2 32. 100 km/hr = ? m/sec 33. 250 m/min =? km / hr 34. 100 m/sec = ? km/hr 35. 250 km / hr = ?m/ min 36. 2 cc/sec = ? L/hr 37. 2L/ hr = ? c / min 38. 2 m3 = ?L 39. 18 L = ? m3 n Tahminleri: Acık
Q1) One way of shaping raw materials into useful and valuable products is through casting process. Casting technology or process is one of the oldest processes in manufacturing field. During the last century, this casting process is used to create gold, jewellery and other products. (i) Draw TWO (2) casting processes that would be most suitable for making a gold and jewellery. (ii) Discuss your answer in (i) (iii) Explain why sand-casting process is not suitable for making a gold and jewellery.