AL=FFh. After INC AL, ZF =a. 0O b. No changeOc. complement of previous carryO d. 1The BSR will set or reset any individual bit of Port A in 8255PPI. (TRUE/FALSE)Select one:TrueFalseWhat is the value in AL atter the following program is executed?MOV AL, BSHMOV BL, ASHNOT ALINC ALCMP AL, BLNEG AL

1. AL=FFh, after INCAL, ZF= correct option is a=0 2. The BSR will set or reset any individual…

AL=FFh. After INC AL, ZF =. O a. o O b. No change Oc complement of previous carry Od 1 The BSR will set or reset any individual bit of Port A in 8255PPI. (TRUEJFALSE) Select one: True O False What is the value in AL after the following program is executed? MOV AL, BSH MOV BL, ASH NOT AL INC AL CMP AL, BL NEG AL

AL=FFh. After INC AL, ZF =. O a. o O b. No change Oc complement of previous carry Od 1 The BSR will set or reset any individual bit of Port A in 8255PPI. (TRUEJFALSE) Select one: True O False What is the value in AL after the following program is executed? MOV AL, BSH MOV BL, ASH NOT AL INC AL CMP AL, BL NEG AL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5/Find the addition result for the following operation (66)8+ (1100)EX-3+(83)10- (F2.1)16 using 2's complement, assume that the result is binary number O 1100000.0001 O 10011111.1111 O None of them O 110000010.111 O 1111101.0001
Q5/Find the addition result for the following operation (66)8+ (1100)EX-3+(83)10- (F2.1)16 using 2's complement, assume that the result is binary number O 1100000.0001 O 10011111.1111 O None of them O 110000010.111 O 1111101.0001
IV) Convert Decimal to Hexadecimal (a) 974510 (b) 2976.5410 V) Convert from Binary to Hexadecimal (a) 10010110101012 (b) 111011101.010101012 VI) Convert from Hexadecimal to Binary (a) 7CAB516 (b) AF2.12B16
What is the purpose of circuit 1 and 2 (highlighted)? How they work? Figure 13. Basic structure of a standard /O port bit Circuit 2 To on-chip peripheral Analog Input Altornate Function Input onvoff I Circuit 1 onlotf Read Voo TTL Schmitt trigger Protection diode on/off Input driver vo pin Write TOutput driver Voo A Protection diode P-MOS Output control Ves N-MOS Readwrite From on-chip peripheral Vss Push-pul, open-drain or deabled Circuit 2 Alternate Function Output ai14781 Bit setireset registers Output data register Input data register SK KH
3rd Class Microprocessor Dr. Mohanad A. Shehab Homework (3): Logical Instructions 1) For register AH • Set bits b0, b3 • Invert bits bl, b6, b7 • Reset bit b2, • don't affect other bits 2) Trace the following program MOV BX, 708EH MOV AX, BX MOV CX, 4802н OR BL, BH XOR BL, AH SHL BL, 01H NOT AH AND AL, 93H SAR BH, CL ROL AL, 01H RCR AH, CL 3) Fill the register AL with the bit 3 of AH, i.e., If b3 of AH-0 then AL must be 00H If b3 of AH-1 then AL must be FFH 4) Rebuild the following instructions 1. MOV AX, 0000H 2. MOV AL, FFH 3. NOT BL 4. NEG CX
(a) Suppose that the BI/RBO input line was connected to ground on the 74LS47 BCD- to-seven segment decoder and all other input lines were connected as shown in Figure 3. Determine the effect this would have on the display. (b) Assume that the switches in Figure 3 are set to binary 1000, but the display shows a zero. What are possible causes for this error? Four DIP switches +5.0 V 1.0 ΚΩ MSB LSB w 330 Ω www 330 Ω 330 ww 330 Ω +5.0 V 7447A +5.0 V R's=330 Voc Anode a w a Lamp test ba ww b BI/RBO CO www RBI Outputs d w e ww e f w ww 8 DUBA BCD inputs GND MAN72 seven-segment display
Q5/Find the addition result for the following operation (66)8+ (1100)EX-3+(83)10- (F2.1)16 using 2's complement, assume that the result is binary number O 1100000.0001 O 10011111.1111 O None of them O 110000010.111 O 1111101.0001