Air with pressure, temperature and density corresponding to a standard sea level condition is allowed to expand isentropically to a state where pressure is 2050 Ib/in^2 and the corresponding velocity is 300 ft/s. Calculate the Mach the second state. (Final answer should be in 4 decimal places).

Q: answer is 900.8 please resolve

A: Given Data

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Consider two infinite parallel plates in length, where the top plate is moving to the right at a…

A:

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Give one problem solving question about "Method of Sections" and show the solution

A:

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: 1. Given the following measurements (in metric and English respectively) of a metal cylinder: length…

A: as you mentioned I solved 1st. one. For solution refer below images.

Q: Piping isometric is produced:

A: This question is based on the concept of the piping isometric.

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

A:

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: What is the difference between corrective maintenance and preventive maintenance ?

A: After equipment fails, corrective maintenance (CM) entails its replacement or repair. When…

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: TXY is suppose to be -40.5 where did -40.7 come from?

A:

Q: Height in mm

A: Given: We have to find the height of the flat workpiece, sine bar is 125 mm which is used to measure…

Q: Find the centroid Y of unsymmetrical I- section shown below with respect to its base

A: Solution:

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: Where did you get the 3 from for the distance of q?

A:

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.