air standard dual cycle receives air at 25 C at 1 atmospheric pressure. The compression ratio is 15, and the cut-off ratio is 2.5. During the constant volume heat addition process, the pressure doubles and the maximum temperature is 2300 K. Determine the heat added in constant volume process. Find the thermal efficie

Q: In an air standard Otto cycle, the compression ratio is 8. Compression begins at 0.1 MPa, 30 degree…

A: Write the given values with the suitable variables. rc=8P1=0.1 MPaT1=30 °CQ=2100 kJ/kgCp=1.005…

Q: In a reheat cycle steam enters the high pressure turbine at 40 bar and 400°C. It expands isentropic…

A: Introduction: In the case of reheating in a steam powerplant, the exhaust steam is reheated before…

Q: 18 and a cut off ratio of 2.2. At the beginning of the compressions process, air is at 100kpa and 27…

A:

Q: The air in the piston-cylinder operates on a Carnot cycle. The high temperature is 800 K, and the…

A:

Q: An Otto cycle has an initial condition of 32 deg C and 105 kPa. The compression ratio is 8 and the…

A:

Q: of heat. Solve for the temperature and pressure at each state point, the thermal efficiency, and the…

A: Here We need to determine the temperature and pressure at each state point, Thermal efficiency and…

Q: Instead, assume variable specific heat An ideal Diesel cycle has a compression ratio of 17and a…

A: Maximum tempreture of the cycle can be found as follows-  T3=𝜌r𝛾−1T1  Where 𝜌 is cutoff ratio and…

Q: 1. An air-standard Diesel cycle has a compression ratio of 15 and a cutoff ratio of 1,4. At the…

A:

Q: 4.) An ideal Brayton Cycle has air at 100 kPa and 25C entering the compressor. After the heating…

A:

Q: 1. An air-standard Diesel cycle has a compression ratio of IX and a cutoff ratio of 1,4. At the…

A:

Q: An ideal Otto cycle has a compression ratio of r=9. At the beginning of the compression process, air…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Show the process on TS- diagram.

A: Given: A reversed Carnot cycle To define: Modifications require to act as a Theoretical vapor…

Q: An air-standard carnot cycle between temperatures of 450R and 1860R. the minimum pressure in the…

A: Minimum Temperature in the cycle = T3 = T4 = 450 R = 250 KMaximum Temperature in the cycle =T1 = T2…

Q: The maximum pressure of an ideal Otto cycle is 5.6 MPa. The compression ratio of the cycle is 8.2…

A:

Q: Show a derivation of final temperature of dual cycle in terms of initial temperature and ratios

A:

Q: The compression ratio of an ideal air Otto cycle is 8. The initial pressure is and temperature are…

A: INTRODUCTION : The Otto cycle is based on the air standard cycle, which uses air as the working…

Q: an ideal Otto cycle with a compression ratio of 8. Find the efficiency of the cycle with the high…

A: The pattern of the Otto motor is known as the Otto cycle. It is the one of most normal thermodynamic…

Q: 1. In an air standard Otto Cycle, air enters at 104.7 kPa and 27°C. The compression ratio is 7:1. If…

A:

Q: The air standard efficiency of an Otto cycle is 50 % and the ratio of specific heat is 1.5, then its…

A:

Q: A gas turbine power plant operating on Brayton cycle shown in figure. The air enters the compressor…

A: given; inlet compressor temperature(T1)=300kexit compressor temperature(T2)=700kturbine inlet…

Q: In a standard brayton cycle, the heat added is 20kW while the heat rejected is 8k. Find the pressure…

A:

Q: An engine operates in an Air-standard Diesel cycle. The net work is 800 kW with air mass flow rate…

A:

Q: An ideal Brayton cycle has a pressure ratio of 8. At the beginning of the compression process, air…

A:

Q: An engine operates on The air-standard Diesel cycle. The net work is 1000 kW with mass flow rate of…

A:

Q: 2. Air is used in a Carnot cycle, the heat supplied is 75 kJ and the isentropic expansion ratio is…

A:

Q: An engine works on otto cycle with compression ratio of 8. The initial pressure and temperature are…

A: Given , Otto cycle . compression ratio , r =V1V2 = 8. P1 = 1 bar. T1 = 50 C = 323 K. P3 = 25  bar.…

Q: compression ratio of 8 is achieved by using an ideal air-standard Otto cycle engine. The working…

A:

Q: Find the efficiency of a diesel cycle with an explosion energy of 3000 J/mol. Air is introduced into…

A:

Q: ng air has the follo neat added to the air °R and K = 1.4. Con

A:

Q: An engine operates in an Air-standard Diesel cycle. The net work is 900 kW with air mass flow rate…

A: Given data:- An engine operates in an Air-standard Diesel cycle. The net work=900 kW air mass flow…

Q: the back work ratio and the thermal efficiency of the cycle assuming a regenerator with 75 and…

A:

Q: Consider a cylinder of a gasoline engine at the beginning of the compression cycle, during which a…

A:

Q: Determine  the thermal efficiency.The adiabatic compression is reversible for An Otto-cycle and  the…

A:

Q: ): Consider a spark-ignition engine in which the effective volume ratio (V1/V2) is 8:1. Compare the…

A: GIVEN DATA- Volume ratio V1/V2=8:1 Pressure at inlet P1=100KPa Isentropic index =1.4 Polytropic…

Q: An ideal Otto engine, operating on the hot-air standard with k-1.34, has a compression ratio of 5.…

A: 1 BTU = 1055.06 j  so 340 BTU = 358,720.4 J- > Heat added   1 Psia = 6.89476 Kpa 13.75 Psia =…

Q: In a standard Brayton cycle, the heat added is 20kW while the heat rejected is 8kW. Find the…

A:

Q: Solve the Problem. Submit your solution with the problem with the submission area. Consider an ideal…

A:

Q: A diesel cycle has an initial temperature of 270C. If cut off ratio is 2.5 and a compression ratio…

A:

Q: generative cycle the inlet conditions are 40 bar and 400°C. Steam is Bleed at 10 bars in…

A: Given:P1=40 barT1=400°CP2=10 barP3=0.8 bar