Air enters the compressor of a gas turbine plant at ambient conditions of 100 kPa and 25 ⁰C with a low velocity and exits at 1 MPa and 347 ⁰C with a velocity of 90 m/s. The compression process is adiabatic, and the power input is 271. Determine the mass flowrate of the air through the compressor.

Q: Air at 90 kPa and 147°C enters an adiabatic diffuser steadily at a rate of 5500 kg/h and leaves at…

A:

Q: 1-Water vapor enters an adiabatic turbine at 6.5MPa pressure and 400 ° C temperature, with a mass…

A:

Q: A compressor operating with 7.7 kg/s water vapour with a compression ratio (P2/P1) equal to 3.0 is…

A:

Q: Steam enters a diffuser at 20 psia and 240°F with a velocity of 900 ft/s and exits as saturated…

A: Assumption is, The flow is steady. Potential energy change is negligible. No work interaction. Write…

Q: Refrigerant-134a enters a compressor at 180 kPa as a saturated vapor with a flow rate of 0.35 m³/min…

A:

Q: 3. Air enters a compressor steadily at the ambient conditions of 118 kPa and 25°C and leaves at 888…

A:

Q: (4) An adiabatic mixing chamber is used to mix 1.36 kg/s of refrigerant R-134a at 1000 kPa and 2°C…

A: Given data: The mass flow rate in one of the inlet tube is m1 = 1.36 kg/sThe mass flow rate in…

Q: In a compressor, air enters at a temperature of 100 kPa and 20 ° C and leaves the compressor at 1200…

A: Given data: The temperature at the entry of compressor is T1=20°C=293 K The pressure at the entry of…

Q: In a water heating system, cold water at 5°C flowing at a rate of 4 kg/s is mixed adiabatically with…

A:

Q: Refrigerant R-134a enters a continuous flow adiabatic compressor as saturated steam at -14oC at 3 kg…

A: Basics of Power plant Engineering.

Q: A hot-water stream at 70C enters an adiabatic mixing chamber with a mass flow rate of 3.6 kg/s,…

A: To calculate the mass flow rate of cold water and rate of entropy generation during this…

Q: Consider an isothermal expansion of 2 lb/sec of air from 100 psia and 90°F to 15 psia. If the…

A:

Q: An open feedwater heater heats the feedwater by mixing it with hot steam. Consider an electric power…

A: Solution: Given Data: ms=0.1 lbm/sPs=10 psiaTs=200oFmf=2 lbm/sPf,i=10 psiaTf,i=100oFPf,e=10…

Q: Refrigerant-134a at 100 kPa and –10°C is compressed by an adiabatic compressor to 600 kPa and 50°C.…

A:

Q: If the turbine is adiabatic, determine the rate of work done by the steam during the process

A: Given: Inlet conditions of turbine 1: P1 = 5 MPa T1 = 600 oC m1˙ = 20 kg/s Steam leaves turbine 1 as…

Q: kPa and at a rate of 2.4ms with an isentropic Air enters an adiabatic compressor at efficiency of…

A: The inlet pressure of the compressor is The inlet temperature is .The volume flow rate is The…

Q: 1) Helium is to be compressed from 150 kPa and 300 K to 800 kPa and 500 K. A heat loss of 20 kJ/kg…

A:

Q: Steam enters the condenser of a steam power plant at 20 kPa and a quality of 90 percent with a mass…

A:

Q: 1) Helium is to be compressed from 150 kPa and 300 K to 800 kPa and 500 K. A heat loss of 20 kJ/kg…

A: Given data, Let us assume point1 as inlet and point2 as outlet. T1 = Initial temperature =300K T2 =…

Q: super heated steam enters an adiabatic gas turbine at 12 bar and 500 °C and leaves at 400 Kpa and…

A: To determine the required values in the above question, we must use two concepts:  1. Continuity…

Q: Ambient air at 100 kPa and 300 K is compressed isentropically in a steady-flow device to 0.8 MPa.…

A: Given: The initial temperature of the air is T1=300 K. The initial pressure of the air is P1=100…

Q: Steam enters a diffuser at 20 psia and 240°F with a velocity of 900 ft/s and exits as saturated…

A: Given: The inlet pressure of the steam is P1=20 psia. The inlet temperature of the steam is T1=…

Q: Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa,…

A:

Q: perheated steam at 0.5 MPa and 400 °C enters an adiabatic nozzle na low velocity and leaves at 0.1…

A:

Q: Air is compressed in an adiabatic compressor. Inlet and outlet conditions are 120kPa, 30 oC and 20…

A:

Q: An adiabatic open feedwater heater in an electric power plant mixes 0.2 kg/s of steam at 100 kPa and…

A: Outlet mass flow rate= 11.7Kg/s And the outlet velocity= 16.83m/s

Q: Steam enters an adiabatic turbine at 2.5MPa pressure and 450C, and at 60kPa pressure and 100C. comes…

A:

Q: Nitrogen at 825 kPa and 450°C enters a steady-flow nozzle with a low velocity (0.45 m/s) and leaves…

A: Write the given data. Pin=825 kPaTin=450 °Cvin=0.45 m/sPex=125 kPa

Q: Air enters the compressor of a gas turbine plant at ambient conditions of 100 kPa and 25 ⁰C with a…

A: ANSWER MASS FLOWRATE 0.808 Kg/s   Solution is given below.

Q: A 3m³ rigid, insulated tank that is initially evacuated is connected through a valve to a supply…

A: