Air at 25°C flows past a flat plate at 2.5m/s. the plate measures 60 cm X 30 cm and is maintained at a uniform temperature of 95°C. Calculate the heat loss from the plate if the air flows parallel to the 60 cm side. How would this heat loss be affected if the flow of air is made parallel to the 30 cm side. what is the percentage change.

Air at 25°C flows past a flat plate at 2.5m/s. the plate measures 60 cm X 30 cm and is maintained at a uniform temperature of 95°C. Calculate the heat loss from the plate if the air flows parallel to the 60 cm side. How would this heat loss be affected if the flow of air is made parallel to the 30 cm side. what is the percentage change.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q7) The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross section is 20 cm x 20 cm. The components in the duct are not allowed to come into direct contact with cooling air, and thus are cooled by air at 30°C flowing (1) SOF wierza -11-22 over the duct with a velocity of 200 m/min. If the surface temperature of the duct is not to exceed 65°C, determine the total power rating of the electronic devices that can be mounted into the duct. Damme Lore
For safety reasons, parts can be directly blown by air. with dimensions of 15 cmx20 cm, which are not allowed to contact printed circuit board, 20 cm long 0.2 opened inside Cold air from a rectangular hole of cmx14 cm will be cooled. from electronic parts The heat generated is transmitted from the thin layer of the card to the duct, where it is combined with the air entering the duct at a temperature of 15 °C. is removed. The heat flux on the upper surface of the channel can be considered uniform and The heat transfer from the surfaces can be neglected. If the velocity of the air in the duct does not exceed (590) m/min and the surface temperature of the duct is constant at 50 °C, this circuit board can be safely placed on it. Calculate the maximum total power of the electronic parts to be placed.
There is a flow of air that circulates over a flat plate that is used to store a food product at a temperature of 95 ° C throughout its surface. The air flows at a speed of 2.5 m/s and has a temperature of 25.0°C. The plate measures 600.0 mm · 300.00 mm. As a task assigned by your plant operations manager, you are asked to answer the following questions: i. Determine the heat loss from the plate if the air flows parallel to the 600.00-mm side.ii. How would this heat loss be affected if the airflow is made parallel to the 300.0-mm side? For this type of configuration, the coefficient of heat transfer by forced convection, h, can be obtained from the relation IMAGE BELOW The previous correlation is valid for the laminar regime, that is: Re < 500000
A square duct having D=23-cm and surface temperature T=70°C is located horizontally in an attic space with ambient temperature T=11°C. If the duct is subjected to ait flow of U=1.4-m/s, find the Nusselt number for the external flow over the duct as shown in the figure below. U air T
Exhaust gases at 1 atm and 300°C are used to preheat water in an industrial facility by passing them over a bank of tubes through which water is flowing at a rate of 6 kg/s. The mean tube wall temperature is 80°C. Exhaust gases approach the tube bank in normal direction at 4.5 m/s. The outer diameter of the tubes is 0.035 m, and the tubes are arranged in-line with longitudinal and transverse pitches of SL = ST = 0.09 m. There are 16 rows in the flow direction with eight tubes in each row. Assume the air properties at 250°C and 1 atm. The air properties at the assumed mean temperature of 250°C and 1 atm are k = 0.04104 W/m·K ρ = 0.6746 kg/m3cp =1.033 kJ/kg·K Pr = 0.6946μ = 2.76 × 10−5 kg/m·s Prs = Pr@Ts = 80°C = 0.7154 The density of air at the inlet temperature of 300°C (for use in the mass flow rate calculation at the inlet) is ρi = 0.6158 kg/m3. The specific heat of water at 80°C is 4.197 kJ/kg·°C. Determine pressure…
A square duct having D=17-cm and surface temperature T=66°C is located horizontally in an attic space with ambient temperature T=14°C. If the duct is subjected to ait flow of U=1.0-m/s, find the Nusselt number for the external flow over the duct as shown in the figure below. U air T,
4. Consider fully developed laminar flow in the annular space formed by two concentric cylinders with a pressure gradient, op/ax, and the inner cylinder stationary. Let r = Rand r = kR. Assuming that the velocity profile is given by u: [¹-( 7 )² + +(ma 1 R R² ap 4μ &x 1-k² In- In(1/k) R a) Obtain an expression for the location of the maximum velocity as a function of k. b) Compare the limiting case, k→ 0,with the corresponding expression for flow in a circular pipe. c) Determine the volume flow rate. d) Find an expression for the average velocity. e) Compare the limiting cases for the volume flow rate and average velocity, k →0, with the corresponding expression for flow in a circular pipe.
A plate with a negligible thickness of 50 cm in width and 100 cm in length and from its upper surface, it is exposed to 2 different airflows in the same direction along its length. top of the sheet The speed of the air flowing from its surface is 3600 m/min and its temperature is 473 K. Its temperature is 298 K and its speed is 600 m/min. The total heat exchange between both fluids calculate. (Assume the initial temperature of the plate is 160⁰C.)
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance
As shown in the figure, electrical heaters operating in the V-220 V are placed on the lower surface of the square-shaped horizontal aluminum plate with a length and width of 1.2 m. Air at a temperature of 27 °C flows from the upper surface of the plate in parallel at 15 m/s. Since the bottom surface of the plate is fully insulated, what should the value of the current () passing through the electrical elements be so that the temperature of the plate does not exceed 77 °C? Air Al plate Heaters L=1.2 m
Air flows over a smooth flat plate; the upstream velocity is 24 feet per second. Determine the distance from the plate's leading edge where the air transitions from laminar to turbulent flow. Use 500,000 for the critical Reynolds number. Answer in feet and include at least two digits after the decimal place. Next