Air at 110 kPa and 35°C flows upward through a 6-cm-diameter inclined duct at a rate of 65 L/s. The duct diameter is then reduced to 4 cm through a reducer. The pressure change across the reducer is measured by a water manometer. The elevation difference between the two points on the pipe where the two arms of the manometer are attached is 0.20 m. Determine the differential height between the fluid levels of the two arms of the manometer.

Q: Water at 20°C is flowing through a horizontal nozzle at a flow rate of 0.005 m3/s. At the nozzle…

A:

Q: n a refinery, fuel ethanol is flowing in a pipe at a velocity of 1.2 m/s at 2 atm. The refinery…

A: Given data v1=1.2 m/sP1=2 atmP2=1 atmd1=40 cmd2=10 cm Here, v is the velocity of flow and P is the…

Q: 2- mass flow rate is

A: To find Enters density mass flow rate

Q: Lane has two pipes connected to each other that transport water because he is very thirsty. The…

A:

Q: The temperature of the air in a balloon is 20 °C and the pressure is 220 kPa. Since the volume of…

A: At initial state the properties of air is:  T1= 20oC=(20+273)=293 KP1=220 kPaV1=0.030 m3 At state 2…

Q: Water at 10°C flows through the system shown in the figure below at 0.38 m³/s. Energy loss in the…

A: Given data:The density of water at 10 degrees celsius isConsider point 1 on the free surface of the…

Q: Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by…

A:

Q: The power 250 W is required to transmit 7 x 103 m³/s of oil that has a head loss of 14 m. Determine…

A: We know that the equation to calculate the power of liquid underflow is: Ph=Qρgh1000 Here, "P" is…

Q: Saturated water vapor at 150°C (enthalpy h = 2745.9 kJ/kg) flows in a pipe at 35 m/s at an elevation…

A: Given data: Temperature of saturated vapour, T = 150°C Enthalpy, h = 2745.9 kJ/kg Velocity, V = 35…

Q: A 0.75-m3 rigid tank initially contains air whose density is 1.18 kg/m^3. The tank is connected to a…

A: Given:- V=0.75m3 ρ1=1.18 kg/m3 ρ2=4.95 kg/m3 To find:- Mass of air entered in tank(mair)=?

Q: Oil with ? = 876 kg/m3 and ? = 0.24 kg/m·s is flowing through a 1.5-cm-diameter pipe that discharges…

A: Given data Determine the flow rate of oil through the pipe if the pipe is (a) horizontal (b)…

Q: A pressurized 2-m-diameter tank of water has a 10-cm-diameter orifice at the bottom, where water…

A: Given:Diameter of tank,D=10 cm⇒Radius of tank,r=D2⇒r=102cm=5 cmAbsolute pressure,Pabs=450…

Q: The diameter of an open-topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily…

A:

Q: A steam turbine carrying a full load of 46 MW uses 77.7 kg/s of steam. The turbine efficiency is…

A: Given: A steam turbine Turbine load = 46 MW ms = 77.7 kg/s of steam turbine efficiency = 78%…

Q: Water is flowing through a horizontal pipe of diameter 250 mm. If the pressure drop between two…

A: Givend=250mm∆P=825Pa

Q: Water flows (from bottom to top) in a vertical duct of 5 cm of internal diameter. A differential…

A: Solution is attached below

Q: The force that drives the flow of fluids is the pressure difference; a pump works by raising the…

A: Power consumed = 3.8 kW Pressure difference = 7 kPa

Q: Air at 110 kPa and 50 °C flows through the 6 cm diameter duct at a flow rate of 45 L/s in the…

A: Data given-  P1 = 110 kPa  d1 = 6 cm = 0.06 m d2 = 4 cm = 0.04 m Q = 45 L/s = 0.045 m3/s z2 - z1…

Q: piezometer and a Pitot tube are tapped into a 4-cmdiameter horizontal water pipe, and the height of…

A: Given data: The diameter of the water pipe is; D = 4 cm. The height of the water column in the…

Q: Rank in order, from highest to lowest, the liquid heights h1 to h4 in tubes 1 to 4. The airflow is…

A: The height of liquid in tube increases with the increase in velocity, since higher the velocity,…

Q: Q2: Glycerin with p = 1252 kg/m and µ = 0.27 kg/m-s is flowing through a 5-cm- diameter horizontal…

A:

Q: Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the…

A:

Q: A venturi meter is placed in a pipe to measure the flow of oil with a specific gravity (SG) of 0.9…

A:

Q: Oil (ρ=1100 kg/m³,u = 5.6 X 10-4 kg/m s) flows through a 4.3 cm diameter pipe. The flow rate needs…

A: Given data:-density of oil, ρo=1100kg/m3dynamic viscosity of oil, μ=5.6×10-4kg/m-sdiameter of pipe,…

Q: The hydraulic lift in a car repair shop has an output diameter of 30 cm and is to lift cars up to…

A:

Q: 12-58 Water enters a hydraulic turbine through a 30-cn diameter pipe at a rate of 0.6 m/s and exits…

A:

Q: A fluid flows at 455 cubic meters per minute inside a rectangular duct, whose cross-section has a…

A:

Q: The power 431 W is required to transmit 3 x 10-3 m3/s of oil that has a head loss of 15 m. Determine…

A:

Q: Consider two liquids of densities p₁ = 1000 kg/m³ and p₂ = 800 kg/m³ that are initially flowing in…

A:

Q: A pump has a required NPSH of 3.0 m. Assuming that the pump is elevated at 3.5 m above sea level,…

A:

Q: The flow rate of ammonia at 10°C (ρ = 624.6 kg/m3 and μ = 1.697 × 10–4 kg/m·s) through a…

A: The sectional area of the pipe can be determined as, The sectional area of the nozzle can be…

Q: he cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m…

A: Given:Radius of tank=r=1mHeight of tank=h=10mNow,area of tank base=A=πr2=π×(1)2=πVolume of…

Q: A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and…

A:

Q: An orifice meter is to be installed in a 12 cm ductile iron pipe carrying water at 27oC. A mercury…

A:

Q: Water in a duct of area 0.1 m2 has an average velocity of 7 m/s. The duct tapers slowly to 0.4 m2.…

A: Given data: The area of the duct at section 1 is, A1 = 0.1 m2. The average velocity at section 1…

Q: /s and thegage pressure at the entrance is 250 kPa. Ignore weight of the fluid and the pipe.…

A: for solution refer below images.

Q: The tank below is cylindrical and has a vertical axis. Its horizontal cross-sectional area is 10 m2.…

A: Given : The horizontal area of cross section of tank = 10 m2 The specific gravity of gasoline = 0.72…

Q: Consider water flowing through the pipe network shown in the figure below. The flow can be assumed…

A:

Q: A steam turbine carrying a full load of 46 MW uses 77.7 kg/s of steam. The turbine efficiency is…

A: Given:  Turbine load = 46 MW ms = 77.7 kg/s of steam turbine efficiency=78% exhausts steam = 26 mm…

Q: hen measuring small pressure differences with a manometer, one arm of the manometer may be inclined…

A: Given:Density of liquid inside the manometer, ρ=900 kg/m3Height of the liquid, h=7.8 inch or 0.198…

Q: 2. Air flows at the rate of 1.5 m³/s through a horizontal pipe with a gradually reducing cross…

A:

Q: Lane has two pipes connected to each other that transport water because he is very thirsty. The…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.