After extraction and prior to evaporation of the organic layer, what experimental step should be performed? O The organic layer needs to be dried with sodium sulfate and filtered. OThe organic layer needs to be tested against litmus to ensure it is basic. The organic layer needs to be tested against litmus to ensure it is acidic. O Performing an extraction was a mistake. A distillation should have been used to purify the desired material.

After extraction and prior to evaporation of the organic layer, what experimental step should be performed? O The organic layer needs to be dried with sodium sulfate and filtered. OThe organic layer needs to be tested against litmus to ensure it is basic. The organic layer needs to be tested against litmus to ensure it is acidic. O Performing an extraction was a mistake. A distillation should have been used to purify the desired material.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Please send me the question in 20 minutes it's very urgent plz
None
1. Fractions are typically collected every 1.5-2 minutes. What effect would taking more fractions every minute have on the distillation experiment?
Question 4 What is the approximate boiling point of the liquid in the mixture with a lower boiling point? Sample Distillation Data 120 100 80 60 40 20 0 0 0.5 00 1 ● 1.5 2 2.5 3 3.5 ● ● 4 4.5
Which of these is NOT true of a good recrystallization solvent? Which of these is NOT true of a good recrystallization solvent? a) The compound is insoluble in the solvent when it is cold. b) The solvent boiling temperature is at least 40 °C. c) The solvent has many impurities. d) The compound is soluble in the solvent when it is hot.
You are attempting to purify a compound via recrystallization. You prepare the process through the following method: 1) Dissolve the material in a minimal amount of hot EtOH. 2) Slowly add hot water until the compound is slightly cloudy. 3) Add a small amount of EtOH until the solution is just clear (still hot). 4) Cool to RT. Upon cooling to RT you notice that the compound is not precipitating out of solution. You decide to boil off some ethanol. Upon completing this step and cooling to RT you notice that the compound is precipitating out as desired! In which solvent is your compound the least soluble? Ethanol O Water O The ethanol water mixture Insoluble in all of these solvents
Based on the melting point of your impure solid, you look at the given samples and believe you havecompound A. Compound A is recrystallized using a mixed solvent system of ethanol and water. You add1 ml of hot ethanol to your sample and it doesn’t completely dissolve. You continue to add hot ethanolbut there isn’t any change. Some solid remains. What should you do next?
Effect of Particle Size on the Rate of Dissolving Time required for all NaCl to dissolve Sample Results after 2 minutes shaking Do you think the size of the crystal makes a difference in how fast the salt dissolves? Explain why the differences you observed and why they happened. Effect of Temperature on the Rate of Dissolving Time required for all NaCl to dissolve Sample Observations Do you think the temperature of the water makes a difference in the rate at which the NaCl dissolves? Explain why the differences you observed and why they happened. Page 3 of 6
Standardization of 0.10 M HCl1. Take three (3) clean and properly labeled 250-mL Erlenmeyer flasks. Into the three flasks, weigh 0.1 g of the primary standard Na2CO3 to the nearest 0.1 mg. Record the weights of the primary standard.2. Add about 75.0 mL of boiled distilled water and swirl to dissolve the solids.3. Add 2 to 3 drops of phenolphthalein indicator. Record the initial burette reading and titrate with the prepared 0.10 M HCl solution until phenolphthalein endpoint.4. Record the final burette reading for each titration in your data sheetDetermination of Ksp and Molar Solubility1. Add Ca(OH)2 to 250.0 mL distilled water with stirring until equilibrium is achieved. 2. Filter the undissolved precipitate. Measure out 50.0 mL of the supernate into a 250-mL Erlenmeyer flask using a pipette.3. Add a few drops of phenolphthalein indicator and titrate with standardized HCl solution until endpoint is achieved.4. Record the volume the HCl solution used. Perform two more trials.…
A gas mixture contains 50% CO2,40% H20, 5% CO and 5% 02. Find a. the concentration of CO in parts per million b. The composition of the mixture based on absence of * .H2O
The answer to c is 1.58g. Please answer question on bottom.
The following test on compounds X and Y were done and the results, list the observations in the table below. Complete the inferences for each test.