after construction, it is discovered that column 3 is not constructed to its intended length of 5m. in light of engineering mechanics, what implications will this have on the middle frame, ( highlighted on RED in figure 1)? what concepts you may use for detailed analysis?

after construction, it is discovered that column 3 is not constructed to its intended length of 5m. in light of engineering mechanics, what implications will this have on the middle frame, ( highlighted on RED in figure 1)? what concepts you may use for detailed analysis?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A truss is loaded as shown in the illustration. Each member in the truss has a circular cross section, a cross-sectional area of 8.0 cm2, and an elastic modulus of 83 GPa. What is the critical buckling force for member A? a) 515N b) 1030 N c) 1550 N d) 2250 N 12 m 12 m 12 m B 100 kN A 12 m 9m
A homogeneous, prismatic beam shown in the figure has a weight of 4.7 kN/m and is carrying a uniformly distributed load, w. It is attached to two cables made of different materials with the following properties: Material Modulus of Elasticity Allowable Stress A 200 GPa 95 MPa B 240 GPa 105 MPa Design the size of the cable such that after the load has carried by the cables the beam will remain in horizontal position. Fill up the table 1 with your design. Table 1: Design of Cables Material Cross-sectional Area (sq.mm.) Actual Axial Stress (MPa) A B See image attach
PROBLEM 1. Given the figure: Indicate direction to your final answer. 2) What is the tensile pull in cord BC in KN? A C 30° 45° 3) What is the vertical reaction at A in KN? 2 m cord 4) What is the horizontal reaction at A in KN? 500 KN B 4 m
Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional Area Modulus of Elasticity AB 1,400 mm2 200 GPa BC 1,800 mm2 200 GPa DB 1,400 mm? 200 GPa C BY 18KN 400mm 400mm 400mm 55.00° 55.00°
The maximum vertical deflection of W8x15 beam subjected to the loads shown in the figure below is closest to which of the following deflection limits: Group of answer choices L/180 L/480 L/270 L/360
The slender rods have a mass of 9 kg/m Suppose that a = 100 mm and b = 240 mm. (Figure 1) !3D Figure 1 of 1> A
Number the components from top to bottom, with component #1 being the 4x10 at the top and component #2 being the 2x12 in the center. The component moments of inertia with respect to x-x axis for components #1 and #2 are denoted by Ixc1 and Ixc2 what are the values of Ixc1 and Ixc2?
I need the answer as soon as possible
Assuming that the members of the truss shown in the figure are deformable and are only subjected to tension and compression. Which among the members attached at joint B will shorten when the external loads are applied? 4 m E 5 m C 4 m B 4 m 80,000 N 60,000 N
For the shown beam sketch: shear moment and deformed shape
Considering beam as axially rigid, the degree of freedom of a plane frame as shown, is
Pls answer neatly and explain step by step A wooden buoy (s.g. = 0.62) is 70mm by 70mm by 26.5m long is made to float in sea water (s.g. = 1.025). How many N of steel (s.g. = 7.85) should be attached to the bottom to make the buoy float with exactly 3710mm exposed above the water surface?