AF-S KN force is applied on steel pipes in -z axis direction. According to connection coordinates of the pipes AD, BD, and CD, please find the forces that are coming to each pipe. F-5 KN AD CD (Coordinates in mm) BD A(230,-380,0) ċ(-440, 240, 0) B(500, 400, 0) ANSWERS T.p(N) (10 pts) TolE (10 pts) (10 pts) 10

AF-S KN force is applied on steel pipes in -z axis direction. According to connection coordinates of the pipes AD, BD, and CD, please find the forces that are coming to each pipe. F-5 KN AD CD (Coordinates in mm) BD A(230,-380,0) ċ(-440, 240, 0) B(500, 400, 0) ANSWERS T.p(N) (10 pts) TolE (10 pts) (10 pts) 10

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A uniform 6.59 m long horizontal beam that weighs 269 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 52° with the horizontal, and a 586 N person is standing 1.16 m from the pin. R. FT 52 1.16 m 269 N 586 N 6.59 m Find the force Fr in the cable by assuming that the origin of our coordinate system is at the rod's center of mass. Answer in units of N.
Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression. A 10 kips Answers: BC= CG= Mi B 11' G Mi 13' 11' C 11 D 5 70° E kips kips
The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom. Neglect the weight of the boom. Don't forget to draw an illustration.
A shelf bracket is mounted on a vertical wall by a single screw. S S2 S1 Neglecting the weight of the bracket, and if s = 6.4 cm, s1 the horizontal force component exerted on the bracket by the screw when a 95.2 N vertical force is applied as shown. Imagine that the bracket is slightly loose. 5.4 cm and s2 = 2.2 cm, find =
The following forces are acting on the bracket below. The bracket has a width w of 2 inches and a height h of 3 inches. The bracket is in equilibrium (not accelerating). Determine F3y knowing F1x-98 lbf and F1y=195 lbf. For this question, what is F3.y in Ibf? Note that the y- direction is pointing up, so if the force is pushing down on the bracket, it has a negative magnitude. 39
A sample of tendon 3.00 cm long and 4.00 mm in diameter is found to break under a minimum forceof 128 N. If instead the sample had been 1.50 cm long and of uniform composition and crosssectional area, what minimum force would have been required to break it?
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
A 89 cm long wire was found to stretch 1.6 mm by a force of 117 N. The wire was round in the shape of diameter 8 mm. Calculate the Youn’g modulus of this wire.
PRO BLEM 2: A TRICKY STRUT An orange strut of length l is connected to a wall via a pi vot at the bottom. An additional (blue rope) also connec ts the strut to the wall attached at an angle 01. A load of weight W is hanging from the strut; the load makes an angle 02 with the strut as shown in the diagram. In order to stabilize the system, and additional force needs to be applied. That force, which is labeled C in the diagram, makes an angle p with respect to the strut as shown. What is o?
Three pairs of flexible cables, spaced at 120° inter- vals, are used to stabilize a 1000-ft television tower. The tower and one pair of cables is shown in Fig. weight of the cables is 3.0 lb/ft. The horizontal component of the force exerted by each cable is 6000 lb. At anchor A, the angle between cable AC and the horizontal must be 40°. Determine The The horizontal distance d from the tower to anchor A. 400 ft B 400 ft KKKKKKKKKKI
The signboard truss is designed to support a horizontal wind load of 770 lb. If the resultant of this load passes through point C, calculate the forces in members BG and BF. The forces are positive if in tension, negative if in compression. 770 lb- Answers: BG- BF- i i B 8' G -4' 6' 6 F in 6' lb lb
The boom of tge wall crane 4m long is held at right angle to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N l, find the tension in the wire and the compression force in the boom Neglect the weight of the boom