Answered: F=500N 60° sul et au .... GAS…

Science

Advanced Physics

F=500N 60° sul et au .... GAS ННИКІННЯкин

Related questions

Q: In an engine, an almost ideal gas is compressed adiabatically to half its volume.In doing so, 2650J…

A: Given information: Here, ΔW is the work done on the system (negative because work done on the…

Q: Two moles of an ideal monatomic gas expand adiabatically, performing 6 kJ of work in the process.…

Q: Calculate the net work output (in J) of a heat engine following path ABCDA in the figure, where V1…

A: PV diagram shown in picture. That refers to the pressure vs volume graph. In the PV diagram, the…

Q: A gas in a closed container is heated with 10 J of energy in an isochoric process. Then, in an…

Q: Air is used in a Carnot engine where the volumes at the beginning of the constant temperature heat…

A: Write the given values with the suitable variables. V1=0.356 cm3V2=5.573 cm3 Here, V1 and V2 are the…

Q: A 0.240 mole sample of an ideal monatomic gas is in a closed container of fixed volume. The…

A: Given, number of moles of ideal monoatomic gas =0.240 molevolume of container is fixed.initial…

Q: moles of an ideal gas at 25°C is allowed to 2 expand reversibly at constant temperature…

A: Solution: given that v1 = 2L v2 = 10 L moles = 2 moles to calculte w, U, H and q

Q: A sample of ideal gas expands from an initial pressure and volume of 32 atm and 1.0 L to a final…

A: a) The required final pressure is, b) For any isothermal process, there will be no change in…

Q: Steam, initially at 700 lbf/in.2, 550°F undergoes a polytropic process in a piston-cylinder assembly…

Q: In a constant-volume process, 216 J of energy is transferred by heat to 0.98 mol of an ideal…

A: ∆W=P∆V=P0 m3=0 J

Q: 1. An ideal monoatomic gas expands isothermally from 0.550 m³ to 1.45 m³ at a constant temperature…

Q: In an adiabatic process, 550 J of net work is done on a gas to significantly reduce its volume.…

A: Given Net work done on the gas= 550 J Process is adiabatic

Q: In a cylinder, 1.20mol of an ideal monatomic gas, initially at 3.60×105Pa and 300K, expands until…

Q: One very special method for performing work is to do so reversibly. A change of state occurs…

A: Given data: Number of moles, n=4 mol Temperature, T=344 K Initial volume, V1=12 L Final volume,…

Q: A monatomic ideal gas with volume 0.195 L is rapidly compressed, so the process can be considered…

Q: We now consider three moles of ideal gas at the same initial state (3.0 L at 273 K). This time, we…

A: Given data, Temperature of ATA=273 K Temperature of B TB=110 K volume=3 L n=3 Constant R=8.314

Q: An ideal monatomic gas expands adiabatically from 0.560 m³ to 1.66 m³. If the initial pressure and…

Q: Part C What is the ratio of the final temperature of the gas to its initial temperature? Enter your…

A: Given Data : Initial pressure, Pi=1.54×105 Pa Initial volume, Vi=7.50×10-2 m3 Final Volume,…

Q: If the gravitational potential energy of the water is equal to the increase in the internal energy…

A: Given data: Water drops from the height of, h=50 m. Specific heat of water is, c=4184 J/kg·K.

Q: Four moles of a monatomic ideal gas in a cylinder at 27 °C is expanded at constant pressure equal to…

Q: What is the final pressure of an ideal gas when it is compressed adiabatically? Consider VVVV, and…

Q: For the atmosphere, write down an expression for thermodynamics for an adiabatic process. -)Write…

Q: In an isochoric process, one mole of an ideal gas of rigid diatomic molecules at volume V is taken…

Q: A cyclic thermodynamic process for an ideal gas has gone through four steps. The amount of heat…

A: we know that Q = U + W

Q: Consider 1 mole of an ideal gas at an initial pressure of 1.00 atm and initial temperature of 273.15…

A: given; n=1 mole Pi=1 atmTi=273.15 KPf=0.435 atmVf=2Vi

Q: Consider the following figure. (The x axis is marked in increments of 2.5 m3.) P (Pa) 6 x 106 4x 106…

Question

100%

By the action of a constant force of magnitude F=500N, the piston of area 0.25 m^2 shown is slowly displaced. Considering that the process is adiabatic, calculate approximately the variation of the internal energy of the gas (in kJ) until the instant when the piston has moved 60cm (there is no friction between the piston and the container).