According to the manual of a certain car, a maximum torque of magnitude 57.0 Nm should be applied when tightening the lug nuts on the vehicle. If you use a wrench of length 0.269 m and you apply the force at the end of the wrench at an angle of 75.00° with respect to a line going from the lug nut through the end of the handle, what is the magnitude of the maximum force you can exert on the handle without exceeding the recommendation?

According to the manual of a certain car, a maximum torque of magnitude 57.0 Nm should be applied when tightening the lug nuts on the vehicle. If you use a wrench of length 0.269 m and you apply the force at the end of the wrench at an angle of 75.00° with respect to a line going from the lug nut through the end of the handle, what is the magnitude of the maximum force you can exert on the handle without exceeding the recommendation?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A flywheel in the form of a uniformly thick disk of radius 1.53 m has a mass of 58.6 kg and spins counterclockwise at 141 rpm. Calculate the constant torque required to stop it in 3.25 min. N.m constant torque:
The figure below shows a fisherman with a fishing pole that makes an angle of 20.0° above the horizontal. The distance from the fisherman's hand to the tip of the pole is L = 1.89 m. A fish is on the line, and it pulls the line with a force of F = 119 N at an angle 37.0° below the horizontal. What is the magnitude of the torque (in N · m) exerted by the fish about an axis perpendicular to the page and passing through the fisherman's hand?
In the figure, what magnitude of force F applied horizontally at the axle of the wheel is necessary to raise the wheel over an obstacle of height h = 0.267 m? The wheel's radius is r = 0.673 m and its mass is m = 1.75 kg. DF
A thin cord is wrapped around a uniform grindstone of radius 0.30 m and mass of 25 kg supported by bearings that produce negligible friction torque. The cord exerts a steady tension force on the grindstone, causing it to accelerate from rest to 60 rad/s in 12 s. (lgrindstone = 5 What is the magnitude of the tension force of the cord? O 5.6 N 11.3 N O 18.7 N O 37.5 N
A man ties one end of a strong rope 9.18 m long to the bumper of his truck, 0.561 m from the ground, and the other end to a vertical tree trunk at a height of 3.30 m. He uses the truck to create a tension of 8.17 102 N in the rope. Compute the magnitude of the torque on the tree due to the tension in the rope, with the base of the tree acting as the reference point. N · m
Two blocks are connected by massless string that is wrapped around a pulley. Block 1 has a mass m1=6.00 kg, block 2 has a mass m2=2.00 kg, while the pulley has a mass of 1.00 kg and a radius of 18.0 cm. When the pulley turns, there is friction in the axel that exerts a torque of magnitude 0.410 N m. If block 1 is released from rest at a height h=1.40 m, how long does it take to drop to the floor?
If the pole makes an angle of 25° with the horizontal, the distance between the point where the line is attached to the pole and the anglers hand is L = 2.45 m, and the fish pulls on the line such that the tension in the line is T = 166 N at an angle 35.0° below the horizontal, determine the magnitude (in N · m) of the torque exerted by the fish about an axis perpendicular to the page and passing through the angler's hand.
Please help me
In the figure, block 1 has mass m1 = 0.460 kg, block 2 has mass m2 = 0.500 kg, and the pulley, which is mounted on a horizontal axle with negligible friction, has radius R = 0.0500 m. Tension T1, the tension force on block 1, is 4.54N. Tension T2, the tension force on block 2, is 4.87N. What is the net torque acting on the pulley? Please note that I know that the answer is to be that taunet = -T1R + T2R Why is the torque associated with T1 negative when it produces a counterclockwise rotation, and the torque associated with T2 positive when it produces a clockwise rotation? I thought that if the direction of rotation was counterclockwise, then the torque is positive, and if the direction was clockwise, then the torque is negative.
Homework
A uniform disk with mass m = 8.75 kg and radius R = 1.41 m lies in the x-y plane and centered at the origin. Three forces act in the +y- direction on the disk: 1) a force 315 N at the edge of the disk on the +x-axis, 2) a force 315 N at the edge of the disk on the -y-axis, and 3) a force 315 N acts at the edge of the disk at an angle 0 = 38° above the -x-axis. +y +x F3 IF, F2
Two buckets of mass ?1=17.5 kg and ?2=15.1 kg are attached to the ends of a massless rope which passes over a pulley with a mass of ?p=8.53 kg and a radius of ?p=0.450 m. Assume that the rope does not slip on the pulley, and that the pulley rotates without friction. The buckets are released from rest and begin to move. If the larger bucket is a distance ?0=2.05 m above the ground when it is released, with what speed ? will it hit the ground?