According to the given graph, answer the following questions : note: The slope of the linear curve is -11.1 *103 (1/K) 10-13 10-14 10-15 0.8 0.9 Reciprocal temperature (1000/K) 1.0 The value of the preexponential is Choose... the value of the activation energy is Choose.. Diffusion coefficient (m2/s)

According to the given graph, answer the following questions : note: The slope of the linear curve is -11.1 *103 (1/K) 10-13 10-14 10-15 0.8 0.9 Reciprocal temperature (1000/K) 1.0 The value of the preexponential is Choose... the value of the activation energy is Choose.. Diffusion coefficient (m2/s)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter4: Temperature Effects On Atom Arrangements And Atom Motion

Section: Chapter Questions

Problem 4.5P

See similar textbooks

Similar questions

URGENT
Question 2: True or False? Please give simple reason for each of them. (1) Diffusion is a time and temperature dependant phenomena by atomic transport. (True/False) (2) Diffusion coefficient varies with respect to host - solute and temperature vary. (True/False) (3) For a specific host - solute at a constant temperature, diffusion distance solute can travel reduces as temperature increases. (True/False)
A square high-density polyethylene [a = 158 × 10-6/°C] plate has a width of 295 mm. A 177 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 45°C, determine: (a) the change in width of the plate. (b) the change in diameter of the hole. Answer: (a) Aw= (b) Ad = i i mm mm
I need the answer as soon as possible
An aluminum cylinder (s.g=2.7) 15 cm high and with diameter d=8.1 cm slides down inside a tube with inner diameter D=8.2 cm, as shown in the figure. The cylinder is concentric with the axis of a tube and between them there is a thin film of oil of s.g. =0.8 with a kinematic viscosity of 0.075St. a) What is the (constant) rate of fall of the cylinder inside the tube? b) determine the torque needed to keep the inner cylinder rotating at an angular speed w=200rpm D
A gate oxide is grown in 640 torr of water vapour at 1050o C. The oxide is grown on a bare (100) silicon wafer. The oxidation time is 2 mins. i) Assuming the tau (τ) value is zero, use the Deal–Grove model to predict the oxide thickness. Do not use design curves. For simplicity, when estimating B and B/A, assume the values are a linear function of temperature, rather than the actual exponential function. ii) When this process is run, the measured oxide thickness is 0.1 µm, but the oxidation rate after 2 mins agrees with the B/A ratio. Find the value of τ that should be used for these process conditions to allow for the initial rapid growth regime
In a two-layer fluid with specific gravities 1.2 and 0.9, a cube of 60 cm is immersed. If the upper and lower halves of the cube are composed of materials having specific gravity 0.6 and 1.4, respectively, then the height of cube above the interface of fluid is cm. [Assume, weight density of water as 9.81 kN/m³] (round off to the nearest integer). Liquid 1: S.G=0.9 S.G=0.6 S.G 1.4 60 cm Liquid 2: S.G=12 30 cm 30 cm
Q-4,
I need the exchange rate and the slope please!
Compute the kinematic viscosity of a R ft long model of ship when the prototype ship length is 500 ft and is travelling with a speed of 20mile per hour in an ocean whose viscosity is 1.2 cP and specific weight is 64 lb/ft3 . Keeping in mind to satisfy the condition that both the Reynolds number and the Froude number should be same. (R is 39)
Please provide a complete solution thank you
5-27 Consider two-dimensional, steady-state heat conduction in a region subject to the boundary conditions shown in Fig. P5-27. The material has a thermal conductivity k = 60 Ww/(m - °C). By using a finite-difference mesh Ax = Ay = 0.3 cm, develop the matrix equation for the unknown node tempera- tures. By solving these equations, calculate the node temperatures. 216 HEAT TRANSFER Insulated T2 T T. T6 GROUP 4 Insulated Convection into medium at T = 30°C with h- 100 W/(m2.°C) T10 T12 11 T13 T14 Tn Insulated T16 T19 T31 Maintained 1.2 cm at 180°C Figure P5-27 -uro g