AC10x25 is connected to a gusset plate with 1-inch-diameter bolts as shown in Figure 1. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total service load capacity if the live-to-dead load ratio is 2.5? Use the exact value of U (eq. 3.1) when calculating Ae.

AC10x25 is connected to a gusset plate with 1-inch-diameter bolts as shown in Figure 1. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total service load capacity if the live-to-dead load ratio is 2.5? Use the exact value of U (eq. 3.1) when calculating Ae.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give me right answer with clear calculations.
2. For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at its end with two lines of 20 mm bolts. Using LRFD, determine the load P that the plates can carry against tensile yielding in the gross section and the tensile rupture in the net section. Use A-36 steel. PL 5x200mm PL 5x200mm Pu PL 10x200mm Pu
Need urgent and correct solution
A C8 x 11.5 is connected to a gusset plate with 7/8-inch-diameter bolts as shown in Figure P3.2-3. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total service load capacity if the live-to-dead load ratio is 3? Assume that A = 0.85A,,. C8 × 11.5
please show all the solutions step by step
A C8 x 11.5 is connected to a gusset plate with 7/8 inch diameter bolts as shown in Figure P3.2-3. The steel is A572 Grade 50. If the member is subjected to a dead load and live load only, what is the total service load capacity if the live to dead load ratio is 3? Assume that Ae=0.85An. Use LRFD and ASD.
The tension member shown in Figure below is a PL 1⁄2 × 8 of A36 steel. The member is connected to a gusset plate with-11⁄8 inch-diameter bolts. It is subjected to the dead and live loads shown. Does this member have enough strength? Assume that Ae = 0.85 An
Can u solve me step by step please . thank u
tf Sec Ag tw W16x100 29.4 0.585 0.985 Bolt (7/8 in) A structural analysis was done for -1 the steel section whose shape and characteristics are shown below, and the outputs were arranged in the table below. Choose the appropriate amount, knowing that .all numbers are in units (ksi, in) O fy ( 36 fu 0.85 20.149 584.3 635.04 58 D(bolt) 7/8 P Maximum tensile force (P) that can be exerted Effective cross- sectional area (Ae) The value of T1 Modulus M (mo) !
please use SI for unit
An L 5 x 5 x tension member of A588 steel is connected to a gusset plate with six -inch- diameter bolts as shown in Figure P3.3-4. If the member is subject to dead load only, what is the maximum total service load that can be applied if the ratio of live load to dead load is 2.0? Use the alternative value of U from AISC Table D3.1 (Consider yielding & rupture limit states only.) a. Use LRFD b. Use ASD L5 x 5 x '½ 1'/2" 5 spaces @ 3" - 15" 12" FIGURE P3.3-4 na.co
Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below. The dead load effect is PD=85 kip while the live load effect is PL=80 kip. Two rows of 5/8 inch standard bolts will be used for the connection and the plate width can be manufactured in 1 inch increments. Assume that the larger connected plate does not fail. Consider the limit states of gross tensile yield and tensile rupture. Find the required tension strength, Pa, for the controlling ASD load combination. Determine the width necessary for the plate to resist gross tensile yield. Determine the width necessary for the plate to resist tensile rupture. Report the required plate width.