A,B and the bearings C, D are located as shown in Fig. The belt tensions are also shown in the figure. Determine the diameter of the shaft. The permissible shear stress for the shaft material is 100 MPa. The combined shock and fatigue

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to…

A:

Q: Two solid 1.625-in.-diameter steel shafts are connected by the gears shown in the figure. The shaft…

A:

Q: maximum shear stress that is generated through the shaft.

A:

Q: A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mm has been designed to…

A: Given: Pressure = 200 Mpa To find: Radial and circumferential stress using Lame's equation Sketch…

Q: A vertical shaft rotated with n revolutions moves by pressing a slot with the force F as shown in…

A: Given, The force acting on vertical shaft, F = 138 N The speed of shaft, n = 690 rpm The radius of…

Q: A shaft with splines of a diameter of 50 mm, as shown in the figure below, transmits a torque of…

A: Given: The diameter of the shaft, d’ = 50 mm The torque, T = 1600 N.m The minimum diameter of the…

Q: countershaft carrying two V-belt pulleys is shown in the figure. Pulley the belt tensions shown. The…

A:

Q: A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be…

A: Here is the solution for the above question.

Q: Two solid 1.625-in.-diameter steel shafts are connected by the gears shown in the figure. The shaft…

A: To find:Maximum shear stress in each shaft

Q: a D C B b C

A:

Q: Form the figure below, the power transmission shaft shows the forces acting on it carrying two…

A:

Q: Situation 4: A rigid plate of negligible weight rests on the central spring as shown and is loaded…

A: Given: The load acting on central springs, P = 5+2x5+4 = 19 kN The gap between outer springs and…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm  no of belt = n = 2 groove angle =  2β = 45° = β = 22.5° power…

Q: As shown in the figure, a homogeneous 100-kg rigid block is suspended by the three springs whose…

A:

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A:

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a…

A:

Q: Problem 4.2 The stepped shaft shown in Figure below is subjected to a tensile load of 32 kN and to a…

A: Given: F=32 kNSut=830 MPaE=207 GPaT=150 NmSy=620 MPa

Q: Figure Q1 shows a solid steel shaft AF which is supported by frictionless bearings at B and F. It is…

A:

Q: A torque of magnitude T= 25,000 lb-in is applied to the end of a tank containing compressed air…

A:

Q: Consider the shaft and keyway shown in the figure below. The shaft has a diameter equal to d= 48 mm…

A: Given data  Diameter= 48mm  Torque Tmin = -320N.m                Tmax = 1380N.m Find the maximum,…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device that absorbs energy from the moving system or any mechanism with the…

Q: ТмотоR Tc = 0.5 kNm 54 mm в Tp =2 kNm 46 mm 46 mm TE = 1 kNm 40 mm F Length of the shaft: LẠC = LEF…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: 4. The shaft shown below, is made of ASTM-A-36 steel with Sy = 250 MPa and p = 7.86 g/cm³. The…

A: The weight density is The yield stress is The torque aplied is The length of shaft is

Q: The end gear (closest to the journal bearing at A) is subjected to the loading shown in the figure.…

A: Given: The yields strength of material = 80 MPa

Q: Parvinbhai

A: The objective of this problem is to draw the shear force and bending moment diagrams for a car jack…

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to…

A: The shear stress in steel is  The modulus of rigidity is The vertical deflection at D is .The load…

Q: Two coaxial closed coil springs make up a standard compound helical spring. When both springs are…

A:

Q: An axle is composed of elements laid by S355 E-module 2.1x105 N/mm2, transverse contraction factor…

A: it appears to be a schematic of a shaft under bending load. Here's how to approach the problem:v)…

Q: A rotary blade rotates at 3500 rev/min. The steel blade has a uniform cross section 3 mm thickness…

A: GivenN=3500 rev/mint=3mmw=30mmd=12mmρ=7800 kg/m3

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G=11,500 ksi] shaft is not to…

A:

Q: An open-coiled helical spring consists of 12 coils, each of mean diameter 60 mm, wire diameter 6 mm…

A: A spring is a mechanical device which is used for the efficient storage and release of energy.…

Q: shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is…

A: Given that ,Power P=75kWspeed N=300 r.p.m Distance b/w bearing =300mm=3mshear stress for shaft…

Q: Q1: For the shaft shown in Figure, which is constructed of two circular cross-section shafts A. and…

A:

Q: The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the…

A:

Q: Material property. This is the only data provided. Dont keep asking for material property.

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.