QUESTION #2(a.) What is the terminal velocity of a composite disc (1 mm thick with an area of 12 mm²), inwater? The density of the composite is 3117 kg/m³.(b.) What is the diameter of a spherical steel particle settling in an oil of viscosity 10 mN.s/m²if its terminal falling velocity is 55 mm/s? The density of the oil and steel are 820 kg/m³and 7870 kg/m³ respectively.

Since you have posted multiple questions, we will provide the solution only to the first question as…

Answered: (a.) What is the terminal velocity of a…

(a.) What is the terminal velocity of a composite disc (1 mm thick with an area of 12 mm²), in water? The density of the composite is 3117 kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Gas Dynamic Lab: 04: Select the correct answer for the following questions. 1. Lift is the component…

A: given; lift is the component of this force that is .......to the on coming flow direction.

Q: Laminar flow occurs when the Reynolds number (Re*) is below 2000; turbulent flow occurs when the…

Q: Atmospheric boundary layers can be estimated using turbulent flow approximations over a flat-plate…

A: Write down the given values along with suitable variables. u = 10 m/s k = 0.41 (Von Karman constant)…

Q: Dry air at 25◦C and atmospheric pressure blows over a 30-cm-square surface of ice at a velocity of…

A: Given data as per question Temperature of dry air, T=25◦C side of square surface, =30 cm=0.3 m…

Q: Construct a flow diagram illustrating the mass and energy exchange between a shining light bub and…

A: Bulb as a system receives electric energy as a high grade energy or work and releases energy in the…

Q: A flat plate with surface area of 3.4 m2m2 is sliding on a horizontal table with 4.2 mmmm thick oil…

Q: 5) Consider a vessel of diatomic nitrogen gas at room temperature. (a) What is the most likely speed…

Q: A particle has a diameter of 0.20 millimeters (Spec.grav = 2.5) falling in a liquid (Spec.grav =…

Q: Consider steady state, laminar flow of a fluid in the -y direction between two parallel and vertical…

Q: Experimental measurements of the convection heat transfer coefficient for a square bar in cross flow…

Q: Oil droplets of diameter 0.2 mm are to be settled from air at 25°C and 1 atm. The density of oil is…

A: Given data:-diameter of droplet, d=0.2mm=0.2×10-3mTemperature of air, T=25°C=298KPressure of air,…

Q: 1-The wind blows with velocity 0.4 m/s parallel to the both sides of a flat plate with rectangular…

A: Note: As per Bartleby guideline only 3 subparts have to be solved at the time. So, upload other…

Q: 6. A mierometer reading is used to indicate the displacement of the (a) boundary layer thickness (b)…

A: 6.

Q: A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high the entire…

Q: i just need final answer Air with uniform velocity of U is flowing over flat square-shape plates…

Q: A fuel cell consists of air (or oxygen) and hydrogenmicro ducts, separated by a membrane that…

A: (a) The area of the duct is written as, The mass flow rate of each duct is written as, The…

Q: hons Example 10.12 A laminar boundary layer on a flat plate has a velocity distribution given by ()-…

Q: A gas at 20°C and 1 atm flow at 6 ft/s past a thin flat plate.At x = 3 ft, the boundary layer…

A: Given data: The velocity of fluid flow is V=6 ft/s. The distance from the leading edge is x=3 ft.…

Q: ! Required information A smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and…

Q: 7.17 Air at a pressure of 1 atm and a temperature of 50°C is in parallel flow over the top surface…

Q: Assume that a radioactive dust particle approximates asphere of density 2400 kg/m3. How long, in…

A: (a) It is assumed that Stokes's law is applied for small particles. The dynamics viscosity is taken…

Q: Еxample -1.1- A plate of size 60 cm x 60 cm slides over a plane inclined to the horizontal at an…

Q: Problem Air at 20 C flows at a velocity of 2 m/s across a rectangular flat plate. The plate is 25 cm…

Q: Consider a 15 μm fuel droplet traveling at 200 m/s relative to the surrounding air. The fuel density…

Q: Example 6. For free flow of air over a plate, it is given that Grashof number is 7 x 10° and Prandtl…

A: Given:Gr=7*109Pr=0.25

Q: A fluid flows at 15 m/s over a wide flat plate 30.5 cm long. For each from the following list,…

Q: Fluid at a uniform speed U flows into a channel between two parallel plates a distance d apart. A…

Q: An ideal gas, at 20°C and 1 atm, flows at 12 m/s past a thinflat plate. At a position 60 cm…

A: Given data: The velocity of flow, V = 12 m/s. The distance downstream from the start of the…

Q: For a 90%-efficient cyclone processing 9000 cfm of air with a pressure drop of 9.0 inches of water,…

A: Given: Flow rate Q=9000cfm or 4.2475m3/s (1cfm=0.00047194745m3/s)Pressure drop ∆P=9 inches…

Q: What will be the terminal velocities of mica plates, 1 mm thick and ranging in area from 6 mm² to…

Q: Air at standard pressure and temperature is compressed adiabatically to 5 atm. What is are the…

A: To find: The value of density and the temperature of the air. Given: The value of pressure after…

Q: cal core sample of 1.5 cm length and 1.2 cm2 cross-section has upstream and downstream pressures of…

A: Given data as per question Length of cylindrical core sample, L=1.5 cm Area of sample, A=1.2 cm2…

Q: A fluid flows at 15 m/s over a wide flat plate 30.5 cm long. For each from the following list,…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Assume water flows over one side of a flat plate with a free-stream velocity of 1 ms-¹. The plate is…

Q: Find the boundary layer thickness (8) equation, the shear stress (t.) and the coefficient of drag…

Q: range of sizes have been detected for the SARS-CoV-2 aerosol dispersed in air inside hospitals. a)…

Q: During the glass plate production process, blocks with a temperature of 1400°C are produced. These…

A: Given data: Temperature at the center of the glass block = T1 = 1400°C Temperature at the sides = T2…

Q: Air at 200C and at a pressure of 1 bar is flowing over a flat plate at a velocity of 3 m/s. If the…

A: Given: Pressure P=1 bar, velocityV=3 m/s, palate is w=0.280 m wide , temperatures are T1=200°C and…

Q: A boundary layer forms on a flat plate which is set parallel to an airstream, at standard sea level…

Q: the entire room once released, the droplets have a density of 1000 kg/m 3, and they do not…

A: Definition:Stokes' lawStokes' law is a mathematical equation that defines the drag force applied to…

Q: Estimate the stopping distance (Xs) and the impaction number N1 for a droplet diameter of 1000…

Q: Flow separation over an airfoil occurs at high angle of attack. Lift coefficient of a wing is less…

A: given; Explain the following: Flow separation over an airfoil occurs at high angle of attack. Lift…

Q: A volcano has erupted, spewing stones, steam, and ash several thousand meters into the atmosphere.…

A: The free-body diagram of a particle of the volcano is given as, Here, Fbuoyancy represents the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: given

VIEW

Step 2: calculation of mass and diameter

VIEW

Step 3: calculation of terminal velocity

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Help me step by step
Three types of pin fins. The fins will be subjected to a gas in cross flow at v= 10 m/s. The cylindrical fin has a diameter of D = 20 mm, and cross-sectional area is the same for each configuration shown in the sketch. D V, Т. V, T. V, T Configuration A Configuration B Configuration C For fins of equal length and therefore equal mass, which fin has largest heat transfer rate? Assume the gas properties are those at T (treat it as air) = 350 K. Hint: Assume the fin can be treated as infinitely long.
Problem 1 (30 points): A 14 kg block falls through a channel which is lubricated by a thin layer of oil with thickness h and viscosity u on both sides. The contact area between the wall and block on each side is A. Determine the terminal velocity, V, of the block given A = 55 cm², µ = 0.35 kg ,and h = 2 mm. m'S %3D Oil film (thickness = || Block V
Air at a pressure of 1 atm and a temperature of 250 °C is in parallel flow over a top surface of a flat plate that is maintained at a uniform temperature of 20 °C. The plate has a length of 0.35 m (in the flow direction) and a width of 0.2 m. The Reynolds number based on the plate length, ReL is 9x10“. (a) Find the rate of heat transfer to the plate. (b) If the free stream velocity of air is increased 5 times and pressure increased 4 times, what will be the rate of heat transfer? For air at 1 atm: assume k=0.0299 W/m.k, Pr =0.70. Draw sketch and show all calculations.
Starting from the basic principles, drive an expression to compute the lift coefficient when the free stream Mach number equals (0.8)
need correct and urgent
(1) Experiments show that in a slightly Viscorur flund at on a молод high speeds the drag force fo exerted on body depends on several parametes. An engineer assumes that the drag force fo is a functon of the budy width normal to the upstream Velocity, I upstream Velouty, ✓, the upstream flud veElucay P viscosity, M, speed of sound, I and the airfoils surface roughnars. " use the Buckingham ♬ Theorem to determine the functional dependence of to on non-dimensional flow similarity parameters (2:) Lot the transition to turbulence occur when I = 1.01m, V= 1·01m/s and M₁P = 1:01·10⁰5 m² s. Calculate the transchen Reynolds number, Retrains.
Problem-2 For the turbulent incompressible boundary layer, the velocity profile is given as u/Ue, y = y/8, Ue and d are boundary-layer edge velocity where, u = and boundary layer thickness, respectively. Using momentum integral equation, prove that: 8/x = 0.383/Re,/5 8% /x = 0.0479/Re/5 and 0/x = 0.0372/Re/5
Given: Asked: Solution:
A cylinder 1 inch in diameter is placed in a hot water pipe at right angles to the direction of theflow. The fluid and cylinder temperatures are at 80 °F and 100 °F respectively. Calculate thevalue of the film coefficient for a mass flow of 2705 lb/hr.