a. What is the name of the circuit in Figure 7. b. Explain how the circuit functions c. Construct a time delay circuit diagram. с.

Q: Find the center (xc, yc) of the given thin plate? Need only handwritten solution only (not typed…

A:

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: The isometric view is given in the above figure.We have to find out multiview of the given isometric…

Q: TS DIAGRAM

A:

Q: In a design, A rectangular object is constructed by connecting four points A (4,2), B(-4,1), C(-2,5)…

A: As per given the rectangle is drawn and its reflection object about point (5,5 ) is also drawn

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: ده ))

A: The mass of each piece is m.

Q: find closure Eq.

A: You have mentoned the postions and angles .

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A: To find: The direction of the resultant measure counter clockwise from the positive x-axis. Given:…

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: 3.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Question 1)   Question 2)

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: Q1. Force F = {270i + 450j –140k} N and it passes point B. The coordinates of the points are: A (21,…

A: Given: The force acting, F = (270i+450j-140k) N The distance between O and B, OB = 21 cm The…

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: Write down berniullis equation

A: It is required to write Bernoulli equation

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a = 2 ft •b = 4 ft • c= 1 ft then,…

A: Consider the free body diagram of member AC, Here,

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

A:

Q: Given the multiview projection of the solid, draw the isometric view. HRP FRP F DA FRP PRP

A: Given the multiview projection of the solid, draw the isometric view.

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: 2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: ## Determining the Net Torque on the Wheel (Considering the Image)The image  shows a wheel with…

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: Identify the drawings as isometric, trimetric, oblque or perspective. A. B

A: Isometric projection is a technique used in technical and engineering drawings to visually…

Q: Find Rab for the circuit fn figure. 202 202 Rab 792 252

A: The circuit is shown below.

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: Given the figure attached, Determine the following: A) What is magnitude of Rand Cr in pt D? (Unit…

A: Solution: Given Data:

Q: The answers should not be in vector form. Please re-anser. Rate will be given

A:

Q: Dotermine ali force truss Shown mem bers of thhe

A:

Q: Calculate each moment by multiplying each force with its distance to the reference point, and add…

A:

Q: Line AB 100 mm long is 30° and 45° inclined to HP & VP respectively. End A is 10 mm above HP and…

A:

Q: Consider the bracket shown in Fig-3. If: • F1 - 10 lb @ -90° • a- 2 ft • b- 4 ft • c-1 ft then, what…

A:

Q: e below shaded area, calculat 130 mm

A: Given Shaded area To find The Inertia about X axis Radius about X axis

Q: P1-10) Sketch the front, top and right side views of the following object. Use the grid provided. D

A: According to the given data A 3-D object is given we need to findThree projection view

Q: Consider for the part in the figure below, a =112, b= 60 and c= 104. 80 Dimensions in mm Analyze the…

A:

Q: • F1- 10 lb @ -90° • a- 2 ft • b-4 ft • c-1 ft then, what is the magnitude of the vertical reaction…

A:

Q: Plzz complete answer. otherwise skip.

A: Given-Infromation: FAB=210NFAC=150N To-Determine: FR,α,β,γ

Q: Q1/3-The B Rep. Scheme for the box consists of: * O 8 faces, 8 edges & 12 vertices O 6 faces, 8…

A: B rep is often known as Boundary representation. This scheme is based on the concept that a physical…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.