a. Refer to the circuit is shown below (a) What is the power factor? (b) What is the average power dissipated? (c) What is the capacitance value that will give a unity power factor when connected to the load? 120 Vrms 60 Hz C Z=10+j1292

a. Refer to the circuit is shown below (a) What is the power factor? (b) What is the average power dissipated? (c) What is the capacitance value that will give a unity power factor when connected to the load? 120 Vrms 60 Hz C Z=10+j1292

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Which type of power supply is required to power up a LVDT? does not matter AC no power supply…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Problem 1: A coil of # 12 AWG copper wire wound in a single layer on a cylindrical form so that the…

A: d(diameter) = 6.0 inches = 6×2.54×10-2 m R = 4 ohm Resistivity of copper, ρ =…

Q: Ferromagnetic materials have this characteristic. A. A relative permeability slightly less than…

A: We are asked to identify characteristics of ferromagnetic materials from the given options.

Q: Discuss causes of insulation failures in high voltage engineering. High voltage engineering

A: according to the question we have to discuss about the cause of insulation failures in high voltage…

Q: Which component provides the potential for work? O Conductors O Load device O Protection device O…

A: POWER SOURCE: Power source is a component with the help of which electrical energy is transferred by…

Q: Wire to be used in buildings and homes in the United States is standardized according to the AWG…

A: A: To calculate the expression of diameter of the wire, simple the expression of gauge number using…

Q: Explain the detailed process of Power Grid Extension

A: Extension of the transmission and distribution network to places where there is insufficient or no…

Question

Clear and detailed Solution

a. Refer to the circuit is shown below (a) What is the
power factor? (b) What is the average power
dissipated? (c) What is the capacitance value that will
give a unity power factor when connected to the load?
120 Vrms
60 Hz
C
Z=10+j1292

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Alternating Current (AC) Series Motor and Universal Motor

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
The average value of a double-frequency sinusoid, sin2(t+), is given by (a) 1 (b) (c) Zero
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
An alternating current varying sinusoidally with a frequency of 50 Hz has anrms value of 20 A.a) Determine the instantaneous value at 0.0025 seconds.b) Determine the instantaneous value, 0.0125 seconds after passingthrough a positive maximum value.c) At what time, measured from a positive maximum value, will theinstantaneous current be 14.14 A?
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
An inductor and a resistor are connected in series with a function generator. The voltage across the inductor is 10.6V pk. The voltage across the resistor is 3.6V RMS. Calculate the magnitude of the total voltage applied to the circuit.
sinusoidal form
Suppose I have two peak phasor voltages, V, = 100245° and V, = 75Z-60°. Circle Your Choices: I. The frequencies associated with the phasors are (0 Hz, 60 Hz, 50 Hz, Unknown). II. The rms value of the first phasor is (100, 70.7, 141, 200) volts. III. If you want to add these two phasors, the frequencies must be (60 Hz, 50 Hz, The same, Integer multiples of a given frequency.)
Please help with the solution.
C. Draw a general sine wave V vs t and I vs t plot for a purely resistive and a purely inductive circuit and show leading lagging parameters and clearly mark the phase difference.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…