a. IfH - 5 m and B - 18°, find the factor of safety against sliding on the roe surface. b. If B = 27", fnd the height, H, for which F, = 1.75.

Q: 5. Determine 8g and eg. Let q = 15 kN/m and L = 6m. _B L L 3 3

A:

Q: . Determine the ratio To/T,

A:

Q: Current Attempt in Progress For the beam shown, calculate the beam slope at A. Assume that a = 50…

A: Question is solved as per previous method but with new values.

Q: 138) p= 150 psi Given: Find: Dmax. Longitudinal Joint Fine = 33x/ft Houp fr Girth joint Fmax = 16k/+…

A:

Q: 5. A 13m bar of negligible weight rests on the smooth planes as shown in the figure. Determine the…

A:

Q: determine the deflection at B in mm using Double Integration Method. Consider 150 mm x 150 mm…

A: INTRODUCTION: Double integration method is the way to simplify the static determinant structure to…

Q: 7. Calculate the vertical displacement AA at A with the graphic multiplication method. (20') 9…

A: Step 1Introduction and questionsThe task is to calculate the vertical displacement ΔA​ at point A…

Q: 500KN 200mm 100mm 45° P

A:

Q: 1. Solve for general and particular solution using homogeneous. (y? + 7xy + 16x?)dx + x² dy = 0 x =…

A:

Q: Deflection at point B in mm. Deflection at point E in mm.

A:

Q: A line was recorded as 2500.00 meters long. The standard tape weighs 0.65 kg, 30.00m long at 20°C…

A:

Q: w= 12 kips/ft 6 kipe D hinge

A:

Q: D2 +3xD-6y =0. Find y(0.2) by Galeskin method.

A:

Q: Situation #2 El is Constant (Assume El = 1 kN-m²) B A kN/m A 7 m B= 8 A= 5 20. Determine the…

A: Given data  EI = 1 KNm2  Find  1. Location of maximum upward deflection from B 2. Maximum upward…

Q: Consider the beam shown in (Figure 1). EI is constant. Use Castigliano's theorem. Figure < 1 of 1 C…

A:

Q: The fuiction Sarce value is 35N and ualue coeffichent Snchon Normal Sarce. 0.32. Find the

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Use Crank-Nicolson method to solve the following PDE a²u ди +b= Эх = au at Over 0≤x≤1 and 0≤t≤3,…

A: Approach to solving the question: the image sequence is 3-2-1....or if seen from reverse then 1-2-3…

Q: By using the Conjugate Beam Method Find the value of EIS at 2m. 80KN/m 4m 2m2 B

A: Given :Required :Value of deflection at 2m from left

Q: For the shaded area, determine the moments of inertia with respect to the given x and y axes.

A:

Q: Solve using Double Integration Method (Indeterminate Beam). Assume EI to be constant. If it is…

A:

Q: Obtain the particular solution of (2x-3y+4)dx+3(x-1)dy=0; when x=-1, y=2 Find th

A: d) Given, 2x-3y+4dx+3(x-1)dy=0   Re-arranging and rewriting the ODE, we have 3x-1dydx-3y=-2x-4…

Q: 3. From the figure as shown, how far will the block move down after three seconds. At t=0, v-0.

A: find distance after  3 sec

Q: below: 40 kN 6 kN/m 2EI El 2m 2m 5m Determine the displacement matrix [A] a. [A] = %D loc O b. [A] =…

A: for displacement matrix  unknowns are taken which are free  i.e... either for rotation or…

Q: The measurements x1 = 8m, x2 = 6m, and x3 = 4m represent the sides of a rectangular parallelepiped…

A: The values given in the question are as follows x1=8 m x2=6 m x3=4 m Systematic errors are ∆x1=0.004…

Q: Ag= 2700mm2 Q1.Determine the net area of angle given in figure 2.10, if 20mm diameter fastener are…

A: Fasteners are utilized in the development business to join at least two articles together in a…

Q: Problems: Analyze the rigid frame given below using either the Portal Method or the Cantilever…

A: Assumption in Portal Frame Method: 1. Point of contraflexure will be at the centre of every member.…

Q: Using DIM, solve for: Ymax (mm) b. Өл (rad) а. 200 IT 50 P (kN) 80

A: For Macaulay's method, Section should pass through udl and should include all the loads acting over…

Q: 2- Find y(2) by using Euler Method if y(1) = 2 and dy = xydx n = 4 use Ans. when x = 2 y = 6.484 and…

A: this question is from approximation Here we are asked use Euler forward approach

Q: Q5. Determine the maximum normal stress in the rectangular bar with a shoulder of circular fillet…

A:

Q: Compute the maximum deflection of the W10 x 39 cantilever beam shown? Neglect the weight of the…

A:

Q: What is meant by COMBINATION FOOTINGS ?

A: Combination Footings or Combined Footings : 1. Whenever two or more columns in a straight line are…

Q: 2. Derive an equation that describes the vertical deflection of the beam, y(x), and also calculate…

A:

Q: the slope at A 7. Determine 8. Determine the slope at B 9. Determine the location of the maximum…

A: Given:- EI = Constant = 1 kN-m2 Y = 32 X = 868 A = 5 To find:- Slope at A Slope at B Location of…

Q: Q5: Results from liquid and plastic limit tests conducted on soil are given below. No. of blows, N…

A: As per our guidelines we are supposed to answer only one question. Kindly repost the other questions…

Q: Find dy by implicit diferentiation if sec(ry) = 6y. dx

A: sec(xy) = 6y..................(1) we will differentiate equation (1) with respect to x

Q: A 10 m 10 kN/m B Problem 2 a. Location of Amax from A b. Dmax

A: Given A fixed beam Required  Location of maximum deflection and maximum deflection value

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.