A. I have a direct-acting pressure transducer 4-20ma built for a range of 0-200 psig. At what pressure should it be giving a signal of 10ma? В. What pressure if it was a reverse-acting transducer and had a reading of 10am? What pressure would it be if it was a 0-10v direct acting pressure transducer and had a reading of 4ma? С. D. Repeat "C" for reverse acting. E. Explain direct acting and reverse acting.

A. I have a direct-acting pressure transducer 4-20ma built for a range of 0-200 psig. At what pressure should it be giving a signal of 10ma? В. What pressure if it was a reverse-acting transducer and had a reading of 10am? What pressure would it be if it was a 0-10v direct acting pressure transducer and had a reading of 4ma? С. D. Repeat "C" for reverse acting. E. Explain direct acting and reverse acting.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Design a clamper to perform the function indicated. Determine the proper value of Voc Calculate the output voltage swing. a. b. 21 VI 10 V -10 V DESIGN th -1.3 V Vo -21.3 V
A given pressure transducer is designed to have a linear relationship between an input pressure and its output voltage. Suppose that input values may range from 30 kPa to 4 MPa, and that the corresponding transducer output voltages range from 0.5 V to 4.5 V. What is the expected output voltage corresponding to an input pressure of 150 kPa? 0.6209 V 1.123 V 1.5 V 3.879 V
Q1. For the circuit shown below, sketch io & Vo. Find the average output Vo& io given a = 60°. а. b. If it is required to obtain an average output voltage of 80% of the maximum possible output, find the firing angle and conduction angle of the thyristor. a = 60° R = 602 Vs = 220V fs = 60 Hz ot Vo L =60mH
حتى الساعة المعطلة تكون صحيحة مرتين في اليوم @sync1 power electronics
A circuit diagram of the Wein bridge oscillator is shown in figure 6. Derive thenecessary conditions for oscillation in this circuit if C1C2= a, R1R2=1b
b) For correct operation as an ac amplifier a JFET must be correctly DC biased to establish an appropriate Q-point, i.e a positive voltage VDs between the drain and source terminals and a negative voltage VGs between the gate and drain terminals. Figure 2.1 shows a circuit that can achieve this requirement. Explain the role of each resistive element in this circuit. Vin RG1 Cin HT lin RG2 VG 3º Rs + VDD ¡VD Cout Figure 2.1 Vout Cs ¡out
can you pls show me the solution
Q1: a) Design the oscillator in Figure 1 to start oscillation with R closed-loop gain of 8.5, then sustain oscillation at a resonant R1 o Vout frequency Assuming of 3.4 kHz. the drain-source IN914 resistance of JFET is 600 N. 2N5458 b) What will be the feedback R2 C2 resistance setting when R3 R4 C3 oscillation is stable? 1.0 kN Figure1
Choose any 4 Questions. Where appropriate, use figures and equations to aid explanation 1.a. What are the two comparator reference voltages in a 555 timer when Vcc = 10 V? 1.b. Determine the frequency of oscillation for the 555 astable oscillators in Figure. 1.c. To what value must Cext be changed to achieve a frequency of 25 kHz? +5.5 V 1.0 kn R₂ • 3.3 ΚΩ Cest 0.047μF RESET DISCH THRESH TRIG 555 GND Vec OUT CONT C₁ 0.01 F 1.d. In an astable 555 configuration, the external resistor R1 = 3.3 k. What must R2 equal to produce a duty cycle of 75%.