a. Find the Thevinin and Norton equivalent circuits at the terminals a-b in the following circuit. b. Find the value of RLmax which, if connected between the terminals a-b, will absorb maximum power. c. What will be the power absorbed if R₁ connected between terminal a-b is equal to 2RLmax. 1 A 50 V + Vth Rth IN RN RLmax 8 Ω www PL if RL=2RLmax 30 Ω 5.2 Ω Σ12 Ω a b

Q: ?Which of the following protects only against over-current (äbäi 2) MCB ELCB O RCCB C Socket C

A: Given, Which of the following protects only against over current

Q: 81 What is the function of the zero-adjust control in a multimeter. it serves to conduct the current…

A:

Q: What is the step by step procedure to use light meter

A: Procedure to use Light Meter Part 1: Setting up an Analog Light Meter            There are various…

Q: could you please help me with item d please

A: Asked to find (d) The inductor current position with respective to inductor voltage? And what angle…

Q: 32. The figure below shows a working surface illuminated by two light sources. What is the total…

A:

Q: 79. Which of the following formulas can be used with Ohm's law to determine the amount of voltage…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: List 6 parts of Multimeter including each corresponding function.

A:

Q: What is the use of the tool marked in the figure? Tools A. To cut the wire B. To joint two wires C.…

A: The tool marked in the figure is,

Q: What are the protection coordination procedure of circuit breakers

A: Protective Devices MOV (Metal Oxide Varistor) fuse Circuit Breaker Relay Lighting Arrester Inrush…

Q: The book says I should have found 46amps. Is this a misprint?

A: as the given explanation in the previous is correct.

Q: overcurrent protection

A: Given :- Transformer rated at 1000V,              Primary overcurrent protection device is at 250%…

Q: 5. Determine the total resistance if each Ris 30. RT M

A:

Q: Choose the correct name of meter which has more number of shunt and series multiplier resistances. O…

A: To increase the range of ammeter shunt multiplier resistance is used in parallel with ammeter. To…

Q: Q3)For the circuit shown below determine the value of current (I) through the resistance R=2N if…

A: In this question,  We need to calculate the current in the resistance R= 2ohm If current in OA…

Q: Vhich of the following is not a factor which affects solar panel efficiency. O a. Temperature O b.…

A: Given To find which parameter does not effect solar panel efficiency.

Q: T The match will at 6pm. * kick off kick in get along go on kick about Fertile soil may be by…

A: 1) Option a- kick off  2)  Option e- Get along

Q: what are the pros of Electric health recorsds List each one? and Ways that each pro is empasized

A: With advancement in technology, medical field started using this electronic health records alot.…

Q: List 6 parts of Multimeter including each corresponding function.

A: Multimeter parts and its function.

Q: в1. What do you mean by static characteristics? Explain any one of the static characteristics. B2. A…

A:

Q: Let the voltage passing through a resistance R = 1000 ± 20 ohm is 10.0 ± 0.1 Volt. The average power…

A:

Q: Explain every step on how to use a multimeter

A: Given: Multi-meter

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: Consider a Type K thermocouple used to measure engine exhaust gas temperature in an automotive…

A:

Q: What is factor of a cable at 5 degrees celcius when calculating resistance

A: The solution is provided in the following section.

Q: List 6 parts of Multimeter including each corresponding function.

A: Multimeter is an electrical instrument which as its names suggest used to measure multiple…

Q: Every PV module is usually affected by the following except

A: Here i have answered this question.

Q: In this lab, you will be using resistors of various nominal values. What are the 5-band colour codes…

A: Given resistor values are: 100 Ohm220 Ohm 390 Ohm 560 Ohm 1000 Ohm

Q: 2. A strain gauge of sensitivity 0.22 / Kg is used as a sensor in weight measurement system. Find…

A: As per Bartleby guidelines we are allowed to solve only one question, since these parts are…

Q: What is The prime mover and conversion of  power in the hydro power station

A: The prime mover and conversion of  power in the hydro power station is-

Q: B. Use this graphic for Questions 7, 8, 9 and 10. V,= 22.5 V R1 2 kQ R2 $5 kO B vs 34 kQ R3 3 kQ -D

A:

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: Problem 1 Label each of the four circuits below as combinational or sequential. A- B 40.5 PRE' A B…

A:

Q: ay you display this in a circuit schematic?

A:

Q: When determining Vs why is the 0.91mohm resistor neglected?

A: Need clarity about the calculation of voltage Vs in the given calculation.

Q: Which type of the following solar system will not have solar tracking mechanism All of the options…

A:

Q: technician A says battery warranties are often prorated. Technician B says some warranties have a…

A: Technician A is definitely correct as many a times the battery warranties are pro-rated. In case of…

Q: Two 36 cell PV modules are connected in series. One is shaded and the other is fully illuminated,…

A:

Q: Determine the approximate value of lo of Figure 52. VDD V. - 9.5V 07 mA 5.22 mA 3.67 mA A MA 1MQ VGG…

A: We need to find out the drain current for given circuit

Q: If the per unit reactance of a power system up to the fault point is 0.1pu and base power (VA 10…

A: Given data Base MVA = 10 MVA Fault point is =0.1

Q: you tell me how circuit breakers and diconnect switches are used to isolate equipmen

A:

Q: A voltmeter indicates that the value of a voltage crossing a load resistance is 5.00 V, this…

A:

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).