1. What are the three resistance ranges available on the Simpson meter? 2. When changing resistance ranges on the Simpson meter, the meter must be zeroed using the Zero Ohm's Adjust knob. What is/are the reason(s) for this step? 3. Where is "00" on the meter scale - on the left or right end? a. Left b. Right 4. Is the Simpson meter more accurate at the left or right end of the OHMS scale? a. Left b. Right c. The meter has the same accuracy across the entire OHMS scale 5. A meter is set to the "Rx100" setting and the needle is pointing to "200" on the OHMS scale. The technician changes to the Rx10,000 setting and the pointer settles over "1.8". Which is the more accurate reading? a. The Rx100 reading b. The Rx10,000 reading c. Either is fine. Neither one is more accurate than the other.

Q: If a voltage spike lasts for 1.5 nanoseconds, what is the frequency of the spike?

A: Voltage spike is defined as sudden rise in voltage which is very higher than normal voltage for very…

Q: Is there a limit to the series voltage a chain of these batteries can achieve?

A: we need to explain given statement.

Q: 1.5 minutes 250mA Find C

A: Given: Time, t=1.5 minutes Current, I=250 mA

Q: R= 180 2 120 V 1000 Hz 30 mH coil Solve for total circuit current. Copy paste these in as needed Q°…

A: In this question we will find current in series RL circuit....

Q: Calculate the RMS current through R2 in the diagram IR1 = 6.06mA peak, R2 = 2.7 kohms, total…

A:

Q: For the waveform of Figure, determinea) Period  I got 100us b) Frequency  I got 10kHz c)…

A: a) Given time = 525usNumber of cycles for 525us =  5 cycle + 1/4 cycle = 5.25 cycle.So period =…

Q: Which of the following statements is true of a shorted component in a series circuit? a. The…

A: Which of the following statements is true of a shorted component in a series circuit...

Q: Prove that Heat rate equals the incremental rate at the maximum efficiency point.

A: Given: Prove that Heat rate equals the incremental rate at the maximum efficiency point.

Q: have a question on why did you use 3 in the equation when solving for the ripple voltage

A: Forward bias of a diode: When Anode voltage of a diode greater than the cathode voltage of a diode…

Q: Which of the following arrangements of three identical incandescent bulbs DRAWS MOST CURRENT from…

A:

Q: For the waveform shown in figure 1 , determine  i - preak value  ii - the peak-to-peak voltage…

A: given waveform

Q: For current drawn, I am confused where 21/40 came from and where 200/21 came from.

A:

Q: 22. Determine the output waveform in Figure 3-87 and draw the timing diagram. FIGURE 3-87 A B C D-x

A: given here a circuit and asked to draw the output waveform. .

Q: When determining Vs why is the 0.91mohm resistor neglected?

A: Need clarity about the calculation of voltage Vs in the given calculation.

Q: Calculate the minimum main protection for 6 A/C air conditioners, their main conductors and the…

A: Step 1:

Q: What is a clamp-on ammeter and what electrical principal does it operate

A: we need to answer What is a clamp-on ammeter and what electrical principal does it operate

Q: If a voltage surge lasts for 20 microseconds, what is the frequency of the surge?

A: Voltage surge is defined as sudden rise in voltage which is able to damage the installed electrical…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.