A 75m course, AB, on level ground was passed by an engineer for the purpose of determining his pace factor. The number of paces for each trial are shown. *Please show the complete solution. Thank you TRIALLINETAPED DIST.NO. OF PACES1АВ75 m85ВА75 m88АВ75 m844BА75 m805AB75 m82A. Determine the pace factor of the engineer.B. If the engineer then took (790,795,793,800 and 799) paces in walking an unknown distance CD, what isthe length of the line?C. Assuming that the taped length of line CD is 700m. Determine the relative precision on the measurementperformed.3.

Given: The length AB is 75 m. The number of paces of AB is, Trial Line Taped dist. No. of…

A. Determine the pace factor of the engineer. B. If the engineer then took (790,795,793,800 and 799) paces in walking an unknown distance CD, what is the length of the line? C. Assuming that the taped length of line CD is 700m. Determine the relative precision on the measurement performed.

A. Determine the pace factor of the engineer. B. If the engineer then took (790,795,793,800 and 799) paces in walking an unknown distance CD, what is the length of the line? C. Assuming that the taped length of line CD is 700m. Determine the relative precision on the measurement performed.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: During concrete pavement inspection of link (3*10) slabs, from airfield section, 4 slabs medium, 12…

A: The deduct value graph for Blow up distress type is shown below:

Q: What concept is explicitly taken into account in the General method for determining development…

A: Factors considered in general method of determining development length Reinforcement bar location…

Q: Structural Analysis Question. Calculate the following, show working.

A: Overturning moment Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Situation 1 Given spot levels determine the total amount of trucks with capacity of 20 cubic meters…

Q: Q1. In Al Mouj, a five storey residential and commercial building constructed by one of the leading…

A: Flat slab is a reinforced concrete slab directly supported by concrete columns, without using beams.…

Q: STA BM1 TP1 TP2 TP3 TP4 BM2 BS HI Determine the elevation of points by differential leveling with…

A: In Differential Levelling Height of Instrument, HI = Elevation + BS ELEV = HI - FS. Where, BS is…

Q: 16. A stone is dropped into a deep well and is heard to hit the water 3.41 s after being dropped.…

Q: Determine the value of Cb using LRFD and ASD. M K 12 ft PL = 16 k WD 12 ft 1.8 k/ft H

A: LRFD: Factored load: WDL=1.2×1.8=2.16 k/ftPLL=1.6×16=25.6 k/ft Compute the reactions for the given…

Q: What commercial size of new cast iron pipe shall be used to carry 4,490 gpm with a loss of head of…

A: Given data in question Discharge constant value Head loss To find out Diameter

Q: Shall reversible moisture movement be taken into account in estimating movementfor movement joints?

A: Brief concept- Moisture- Water content in form of vapours or droplets is termed as moisture and its…

Q: 56. In case of bridge greater than 10.7m in height and which cannot be inspected from beneath due to…

A: GIVEN: Bridge greater than 10.7m in height, which cannot be inspected from beneath due to watery…

Q: A stone is thrown with an initial velocity of 250 m/s upward at 60° to the horizontal. Neglect…

Q: Bull floating is done: O A) Immediately after hand floating OB) Before screeding C) Immediately…

A: Reference : Concrete technology, Methods used for leveling Concrete. Bull Floating : A tool called…

Q: Define the accuracy of the dumpy level ?

A: In the question we have to define the accuracy if dumpy level. Dumpy level is an instrument leveling…

Q: 5. Answer the following 61 10'

A: Solution

Q: Find the grade resistance, for a 2500 Lb car traveling on a 2.5° uphill grade. Show All Work:…

Q: Answer the following by True or False (Note: each one wron answer). Choose 5 only. 1- Mechanical…

A: This question is related to the Soil Mechanics from Civil Engineering. This is True false based…

Q: A stone dropped from a bridge strikes the water in 5 seconds. Find the speed with which it strikes…

A: The basic formula used are v=u+ats=ut+12at2 Here v is the final velocity, u is the initial velocity,…

Q: A stone is thrown vertically upward with a vertical velocity of 49 m/sec. It returns to the ground…

A: Given data : Initial velocity (U)=49 m/sFinal velocity (V)=0

Q: At what angle 0 must the 400-N force be applied in order that the resultant R of the two forces have…

Q: unit load As/Rs for work-in-process storage in a factory must be designed to store 2000 pallet loads…

A: It has been asked in the question to determine the dimensions of the rack structure

Q: Q6 (b) How would you go about performing the following tests and what are they used for? (i)…

A: a) Penetration test: The penetration test is utilized as a proportion of consistency. Higher upsides…

Q: To get the best paving stones in the curve, we use stones of lengths

A: To get best paving stones in the curves, we try to use stones of lenths "shorts" Acoording to…

Q: SHOW STEP BY STEP SOLUTION, FORMULA USED, AND INCLUDE FIGURES/DIAGRAMS

A: Step: 1 Velocity: - It is defined as the speed at which any object moves in a specific direction.…

Q: True or False? Pallet truck is a piece of material handling equipment that allows the operator to…

A: True:- A pallet truck can be defined as a device that can greatly facilitate moving and lifting…

Q: If there is a risk of falling into operating machinery, some form of fall protection must be used. O…

A: Use of machinery is an unavoidable component in industries. The risk factor related to operating…

Q: 21) A 200 ft² billboard is located in along Route 18 near New Brunswick (Zip Code 08901) Atlantic…

A: Given Data:Area A=200 ft2G=0.85Cf=1.6Kz=1.2Kzt=1.0Kd=1.0

Q: ● ● From the following measured interior angles of a triangle, calculate the adjusted interior…

Q: Why Le chatliers apparatus is used ?

A: The Le chatliers apparatus is used to determine soundness of cement.

Q: 16. QUESTION SIXTEEN The basic action involved in sheep foot rolling is: A) Pressing B) Kneading C)…

A: Answer :- 16 Option b Kneading The basic action is kneading of the soil sample through the…

Q: boater considers dropping the motor Into the water to create waves , describe the resulting of the…

A: The phenomenon of motion is when an object changes its position over time. Displacement, distance,…

Q: Water flow through a 100 mm diameter pipe with a velocity of 0.015 m/sec. If the kinematic viscosity…

A: Diameter of pipe = 100 mmkinematic viscosiy of water = 1.13 X 10-6Velocity of water = 0.015 m/secTo…

Q: A 162-foot roll of #10 wire is used when installing a residential airconditioningunit. Lengths of 17…

Q: Neatly sketch and explain the constructional features of a Crane with runways installed on columns…

A: Solution: Theory that is based on the Column style jib Crane: The BZ model column style jib crane…

Q: PLEASE ANSWER QUESTION AND SHOW WORK. I NEED TO STUDY THIS. The SUBJECT IS TRANSPORTATION "Civil…

A: Therefore, the length of the guardrail (X) is approximately 1360.209375 feet.Explanation:Step 1:LH=…

Q: A concrete structure with a minimum dimension of 150 mm, concrete cover of 30 mm, and rebar spacing…

Q: The restaurant below has 4 booths (2 benches each), each bench is 54 inches in length and 8 fixed…

A: We need to find occupant load for the given small restaurant

Q: t compression test. Discuss from the beginning to end using your own wo

A: Compression testing involves subjecting a material or product to forces that push, compress, squash,…

Q: Fall protection is generally required in Construction over? O 4 ft O 6 ft O 8 ft 10 ft

A: Fall hazards occur in construction works mainly due to falling of materials and tools over workers…

Question

A 75m course, AB, on level ground was passed by an engineer for the purpose of determining his pace factor. The number of paces for each trial are shown.

*Please show the complete solution. Thank you

TRIAL
LINE
TAPED DIST.
NO. OF PACES
1
АВ
75 m
85
ВА
75 m
88
АВ
75 m
84
4
BА
75 m
80
5
AB
75 m
82
A. Determine the pace factor of the engineer.
B. If the engineer then took (790,795,793,800 and 799) paces in walking an unknown distance CD, what is
the length of the line?
C. Assuming that the taped length of line CD is 700m. Determine the relative precision on the measurement
performed.
3.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

What are the main things needed to find the finish flow and elev
I need a quick solution within 10 minutes With my best wishesTon.
H.W/ A longitudinal section survey was conducted for the purpose of implementation of the sewer pipe with longitudinal slope of (-0.5%) and deep (94.7cm) from the beginning of the project. With the help of the longitudinal section details shown in table below, Draw the longitudinal section and the sewer pipe details with reasonable scale. sta. B.S. H.I I.F.S. F.S. Elev. B.M1 0.663 132.230 0+15 1.946 0+30 1.008 0+33.5 1.83 0+45 1.153 T.P1 2.787 1.585 0+60 2.27 0+75 1.218 0+81.3 0.765 0+90 0.646 1+05 0.682 Т.Р2 0.961 1.122
a) 200-ton, nominal rating crawler-mounted crane with 180 ft of boom has a radius of 60 ft what is the lifting capacity? b) What is the travel time for a scraper moving at 21 mph over a distance of 0.587 mile?
H.W/ A longitudinal section survey was conducted for the purpose of implementation of the sewer pipe with longitudinal slope of (-0.5%) and deep (94.7cm) from the beginning of the project. With the help of the longitudinal section details shown in table below, Draw the longitudinal section and the sewer pipe details with reasonable scale. sta. B.S. H.I I.F.S. F.S. Elev. B.MI 0+15 0+30 0.663 132.230 1.946 1,008 0+33.5 1.83 0+45 L.153 T.PI 2.787 1.585 0+60 2.27 0+75 1.218 0+81.3 0,765 0.646 0.682 0+90 1+05 Т.Р2 0.961 1.122
The newly constructed beidge in your town is a steel arch beidge 600m length. How much does the total length of the roadway decking change between temperature extremes of 30°C and 50.0°C?
But how would I plot the stresses as a function of L/h ?
A ball bearing operates at 3000RPM, and has a life of 50,000 hours, 6500hours and 1000hourswhen subjected to constant amplitude loads of 1kN, 2kN and 4kN. During each hour of operation,the load is 4kN for 5min, 2kN for 15min and 1kN for 40min. Given this information, determinethe total damage caused by this loading sequence on the ball bearing. Also, determine the life ofthe bearings in terms of hours. What percentage of the damage is caused by each of the loadingindividually?
This is a testing method performed to check overall straightness of the tower.
Define Typical load–deflection plot.
Solve the problem completely. Support your solutions with diagrams. No short-cut in your solution
A borderline tree in a BAF 10 ft?-ac1 cruise has an 18 in. DBH and you measure horizontal distance to the center of that tree at 42.5 feet. Is the tree tallied? Show your work.