A. A metal plate weighing 4 kN/m? is being lifted slowly by cables AC and BC. Calculate the distance "x" for which the plate become equilibrium. If each cable has a diameter of 25mm. determine also the stress in the cables

A. A metal plate weighing 4 kN/m? is being lifted slowly by cables AC and BC. Calculate the distance "x" for which the plate become equilibrium. If each cable has a diameter of 25mm. determine also the stress in the cables

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A transmission tower is loaded as shown in the figure JCZ-1. Assume roller support at A and hinge…

A: Determine the stresses at member CE and DF.

Q: B around the smooth peg at E, a vertical cable at e at D. Determine the weight of the heaviest bar e…

Q: Two blocks are connected by a light, flexible cable that passes a frictionless pulley. Block A…

Q: The homogeneous bar shown below is supported by a smooth pin at C and a cable that runs from A to B…

A: Free Body Diagram of the given assembly:

Q: 4. (a) A cantilever AB of length Im carries a uniformly distributed load, w N/m from the fixed end A…

A: Above given data we have to find total permissible load w

Q: The system in the figure is in equilibrium. Aconcrete block of mass 349 kg hangs from the end of the…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: P=545N To find tension in cable BE and BD

Q: The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and…

A: The length of bar ,L =750mmThe torques applied are 80Nmclockwise, 20Nmanti clockwise, 30Nmclcok…

Q: Two cast iron pipes are held together by a bolt as shown. The outer diameters of the two pipes are…

Q: 2. What is the maximum bending moment that can be applied to the section without causing tension at…

A: Given Effective stress=600MPa b=275mm d=550mm

Q: Question1 The uniform rectangular plate of mass m is suspended by three cables. Determine the…

Q: Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt…

A: We have to find out the unit stress in each bolt with the given data,

Q: A tubular post of outer diameter d₂ is guyed by two cables fitted with turnbuckles (see figure).…

Q: A solid steel shaft is to transmit a torque of 10 kN-m. If the shearing stress is not exceed 45 MPa,…

A: Given: Torque transmitted by solid steel shaft, T = 10 kN-m Maximum shearing stress, τmax=45…

Q: 1. A solid steel shaft in a rolling mill transmits (10 + 1) kW of power at 2 Hz. Determine the…

Q: A 2000-kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-sectional…

A: Determine the location x of the largest additional force P which can be applied to the bar.

Q: Ends A and D of the two solid steel shafts AB and CD are fixed, while ends B and C are connected to…

A: Hi! Thank you for the question As per the honor code, We’ll answer the questiononly in typed…

Q: A 2000-kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-sectional…

A: Determine the location x of the largest additional force P,X=?

Q: Situation 29 The homogeneous bar shown in the figure below is supported by a smooth pin at C and a…

A: Cable diameter (d) = 0.6 in. Determine the stress in the cable.

Q: A pulley is keyed to a shaft midway between two anti-friction bearings. The bending moment at the…

A: Bending Moment at pulley varies from 170N-m to 510 N-m Torsional moment in shaft varies from 55N-m…

Q: QI-The homogeneous bar ABCD shown in the Figure is supported by a cable that runs from A to B around…

A: As per guidelines we need to answer only first question so please repost rest question separately.

Q: The hollow steel shaft (G 83 GPa) must transmit a torque (torsional moment) of 32.5 kN-m. The outsid…

Q: 1) If the radius of cables AB and CD are 5mm and modulus of elasticity is 20GPA, calculate the…

A: It is asked to find normal stress and normal strain in cable AB & CD.

Q: If the couple moment acting on the pipe has a magnitude of 400 N.m, determine the magnitude F of the…

Q: (c) A vertical tie fixed rigidly at the top, consists of a steel rod 2.5 m long and 20 mm diameter…

A: Given data, Eb = 100 GPa Es = 200 GPa mg = 10 kN Diameter of steel = 20 mm Internal dia of brass =…

Q: Situation No. 1 A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the…

Q: 1. A solid steel shaft in a rolling mill transmits (15 + 1 3) kW of power at 2 Hz. Determine the…

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown. Each spring consists…

Q: The two-bar structure shown is pinned at A, B, and C. A sign weighing 20 kN is suspended from bar BC…

A: To find outer diameter of bar AB

Q: nner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear the tube when the…

A: According to given data

Q: The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and…

Q: A homogenous bar AB, 1000 kg in mass, is suspended from cables AC and BD as shown. The…

Q: Calculate the maximum shear stress in the beam: 50 N/M 10mm 30 mm 10 mm 10m 40 mm

Q: 1. A tower guy wire is anchored by means of a bolt at A. The tension in the wire is 4000 N.…

Q: 3. Three cables are joined at the junction ring C. Determine the tensions in cables AC and BC caused…

Q: A solid steel shaft in a rolling mill transmits 20 kW of power at 2 Hz. Determine the sma diameter…

Question

A. A metal plate weighing 4 kN/m² is
being lifted slowly by cables AC and BC.
Calculate the distance "x" for which the
plate become equilibrium. If each cable
has a diameter of 25mm. determine
also the stress in the cables

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 2000-kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-sectional area 500 mm, as shown. Determine the location x of the largest additional force P which can be applied to the bar. The stresses in the cables AC and BD are limited to 80 MPa and 70 MPa, respectively. 18m 18m 2 in
Question1 The uniform rectangular plate of mass m is suspended by three cables. Determine the tension in each cable. 0.8 m 0.3 m 0.4 m 0.3 m R -0.8 m B 0.5 m-
please answer in the nearest three decimal numbers don’t cancel the question please
3-24. The wires AB and BC have original lengths of 2 ft and 3 ft, and diameters of in. and in., respectively. If these wires are made of a material that has the approximate stress-strain diagram shown, determine the elongations of the wires after the 1500-lb load is placed on the platform. 30
The two-bar structure shown is pinned at A, B, and C. A sign weighing 20 kN is suspended from bar BC at points D and E, which are located at 0.8 m and 0.4 m, respectively, from the ends of the bar BC. If member AB is a steel pipe with inside diameter 20 mm, determine the smallest permissible outer diameter of the member if the working stress in steel is not to exceed 140 MPa.
ASAP 10 MINS
Problem 2 (for all students). Determine the state of stress, the principal stress and the max in- plane shear stress at point B on the cross section of the pipe at section a – a. Indicate the results on a differential element at the point. a 300 mm B, 300 mm a |6 kN B.50 mm TA - 40 mm Section a - a
Three pulleys are joined by solid steel shafts AB and BC. If G = 200 GPa, determine the unit shearing stress in shafts BC. In MPa A 25 mm ara B 450 N-m 1.2 m 1300N-m 38 mm dia 1.80 m 900 N-m
The staves or vertical members of the wooden tank are held together using hoops having a thickness of 19 mm and a width of 54 mm. The spacing of hoops is 291 mm. The wooden tank has a radius of 479 mm. Determine the stress in hoops (kPa) if the tank is subjected to an internal gauge pressure of 17 kPa and this loading is transmitted directly to the hoops. s/2 s/2 AC B-
Practice prob2 show solution
rities: The homogeneous bar shown below is supported by a smooth pin at C and a cable that runs from A to B around the smooth peg at D. Find the stress in the cable if its diameter is 0.6 inch and the bar weighs 6000 lb. 3 m B 5m 5m
Ends A and D of the two solid steel shafts AB and CD are fixed, while ends B and C are connected to gears as shown. Knowing that a 6-kNm torque T is applied to gear B, calculate the maximum shearing stress (a) in shaft AB, (b) in shaft CD. 40 mm 384 mm C 200 mm 20mm 600 mm