a. A member ABCD is subjected to point loads as shown in figure Task 2.b. Calculate (i) Force P necessary for equilibrium (ii) Stress developed in each section (iii) Also draw free body diagram for individual section 2500mm2

Q: termine the critical path by filling the table below  What is the length of this project in days?…

A: To find: The critical path and the length of the project.

Q: A drive system consists of single strand chain running on a 22 tooth drive sprocket at 1600 rpm. The…

A: Solution: Given Data: Ts=22Ns=1600 rpmP=0.5"NL=280 rpmC=D+0.5d

Q: An installer can work 63⁄4 hours each day at a worksite. The installer will need303⁄8 hours to do a…

A: Given Data⇒ Time for which installer can work at a site a dayt=634 hours Time needed to install a…

Q: The extension, y, of a material with an applied force, F, is given by y = eFx1x10-3. a) Calculate…

A: Find out:Calculate the work done if the force increases from 100 N to 500 N using:An analytical…

Q: Water Wheel Design You have been asked to design a water wheel that will generate electricity from a…

A: Given : To find : Mathematical model

Q: reciprocating saw needs to move the blade downward 0.75 in in 0.10 s anc turn in 0.08 s. Determine…

A: As per company's guidelines we can answer only 1st question

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: The specific speed of turbine is 85 rpm and running at 450 rpm. The effective head is 20m and…

A:

Q: There is a drill string with a weight of 530000 lb that is pulled up at 100 ft/min. The number of…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Let's work through the calculations for the given L-shaped object.### Part a: Finding the x-centroid…

Q: Question 101 # A) A projectile has a firing velocity of 84 m/s at an angle of 37 degree to the…

A:

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: The output of a certain machine can be increased if it undergoes a major overhaul now and it will…

A: P = $20,000 (P/A, 15%, 5)    = $67,044 finding A when given F, Given a future sum of money, F, how…

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: 18. A car starts from rest at a point A and increases its speed at a constant rate as it enters a…

A: Given: Total magnitude of the velocity at point B: →a=2.5 ms2 Because car starts from A at zero…

Q: 6 m

A:

Q: A flat belt of thickness 11 mm is used to transfer power between from electric drive motor running…

A:

Q: Design the biggest box (volume) without cover that made from 6m² of aluminum. Hint: Use Lagrange…

A: Objective -  designing the biggest box (volume) possible made up of area of 6 m2 .

Q: please calculate at least 3 decimal places a) Draw a sketch where you replace the distributed…

A:

Q: 27. You have the following compound machine. For and What is the ideal mechanical advantage of this…

A: We have to calculate compund machine

Q: Very very urgent. Point C is the starting point of the ski and landing track and the landing track…

A: Please see the attached detail solution:

Q: the net engine power of a tractor is 35 HP, what is the approximate power available at the drawbar?

A:

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

A:

Q: to the ght rigid bar are identical except for ength. Before the load W = 6500 lb. ras attached, the…

A:

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

A:

Q: Question 3. The purchase price of a natural gas-fired commercial boiler (capacity X) was $181,000…

A: Given Data The price of boiler 8 years ago was $181000 Assume that the cost of the new boiler is:…

Q: Does this machine maximize or minimize the force (100 Ib) *

A: Reaction force acting on the point B is RB×1.5=100×20RB=1333.33 lb As the reaction force acting at…

Q: 2) Orthogonal Cutting: Consider a person who is shoveling snow from the sidewalk. This person can…

A: To find: The ratio of the force for shovel A to the force for shovel B.Given:Coefficient of friction…

Q: Q5) Assume that 2 automatic machines have been assigned to one operator. It takes 2 minute to load a…

A: Given:

Q: Confined

A: given Identify actions required before approving Start of Work in a Confined Space.

Q: An aluminum cube of edge length 20 cm floats on mercury. How much extra depth will the cube sink…

A: Consider at a particular temperature the aluminum cube sinks a depth h and density of mercury is .…

Q: Subparts 1, 2, and 3.

A:

Q: It is required to design a tennis ball for recreational use by settlers on Mars. The primary…

A: Given data:LE - Drop height on Earth (m) = 2.54 m gE - Gravitational acceleration on Earth (m/s2) =…

Q: Problem 5: Write the MOST equation for the task and calculate the Standard time for the process (in…

A: Given question: Write the MOST equation for the task and calculate the Standard time for the process…

Q: 1. Write the procedure for shaper process.

A: Shaper process is the process in which unwanted metal surface is removed by a single-point cutting…

Q: 5. What is the degree of freedom if the number of independent equations are 5 and the number of…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.