A yucncy iesponse transfer function of a certain electrical circuit is as given below. Simplify the following transfer function to write the magnitude equation in (dB) and the phase equation and what are the important angular frequencies for its magnitude fequency 1csponse (Note: Bode plot is not required). (j 20w) (3+ jw) H(w) = (2+ jw)(6+ jw)²

A yucncy iesponse transfer function of a certain electrical circuit is as given below. Simplify the following transfer function to write the magnitude equation in (dB) and the phase equation and what are the important angular frequencies for its magnitude fequency 1csponse (Note: Bode plot is not required). (j 20w) (3+ jw) H(w) = (2+ jw)(6+ jw)²

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering will upvote . Need matlab knowledge these are the parts that need to be answered. ons: Calculate the cutoff points. Show a screenshot of your circuit. Are the calculated cutoffs being reflected on the theoretical Bode Plot? Include a screenshot of your codes and the theoretical Bode Plot with both cutoff points labelled. How well did the filter perform when processing the 10HZ and 15OHZ combined signal? Include a screenshot of the Scope. The transfer function for the band pass filter is given to you (equation 9). How was this derived? Show the steps starting from how you use the circuit to get the equations representing the circuit to how you solve the equations to get the final version. Given is that it is an RC Bandpass circuit with r1=10kohm, r2= 100kohm ,c1=1uf ,c2=0.001uf. the RC bandpass circuit proceeses 10hz and 150 hz combination. equation 9 needed for part 4 mentioned above is wC1 R Vw? (RCi+R1C2+R2C2)²+(1–w?C,C2R, R2)2 %3D
-3. Determine the Ayquist rate for each of the Co following signals assuming the dyquist. nate for act) is fs Hz. of offs Bad/sec, a) gixel) b) 4₂ (4)= c) (z (t) = d) fult) = dae(t) dz 2<² (t) xelt) cos & fs t
??
Find the theoretical resonant frequency of the circuit shown by using the resonance frequency formula. Find the transfer function IR2(s)/V2(s), s=jw.
In the RLC parallel circuit below, Q-50. Determine the resonant frequency (in rad/s), BW (in rad/s), and R. At resonance, what is the current going through the inductor? 0.120A CFIUF L 21H √1,=?
Solve the problem.
Will upvote
I want different solution, in easier way which i can understand, not similar answer.
Express the transfer function (Vo(w)/Vin(w)) and draw the bode plot of both magnitude and phase of it.
13s2+26s+39 Q4- Draw the Bode Plot for the transfer function: s(s2+9s+20)(3s2+4s) mark the margins and crossover frequencies on your plot.
The magnitude and phase diagrams are provided for a passive filter. Input signal vin(t)=15 cos(20000t+100°) V is applied. What is the output voltage in V when t-1ms ? Series RLC H(s) -20 -30 -40 700 10 10 180 150 ... ... ... ... 100 ... 50 10 10 Frequency (rad'sec) Phase (deg) Mag (dB)
C: For the circuit shown, is this a possible Bode Plot? (R1 = R2) B1 B R2 R1 C1 b Odb Gain N Frequency