A working fluid in a closed loop undergoes the following cycle:• 1-2 Isentropic compression• 2-3 Isobaric heat addition• 3-4 Isentropic expansion• 4-1 Isobaric heat rejectionIdentify the temperature-entropy (T-s) diagram that illustrates this cycle.T2.123344S21213344S

Answered: Image /qna-images/answer/ecf7ac75-b35a-4b12-9ea1-062b0b74c0ff.jpg

Answered: A working fluid in a closed loop…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

After graduation, you take a job with the Acme energy services company. Your first job is to purchase high efficiency heat pumps. The heat pumps employ mechanical power and a heat engine to provide heat at TH = 100°C. A low temperature heat sink at TC = 20ºC is also available. A salesman shows you two models. Performance data for each model operating at steady state are provided in the Figure below
Air within a piston-cylinder assembly executes a Carnot heat pump cycle, as shown in the figure below. For the cycle, TH = 500 K and Tc = 300 K. The energy rejected by heat transfer at 500 K has a magnitude of 1000 kJ per kg of air. The pressure at the start of the isothermal expansion is 325 kPa. Tc. p-v diagram for a Carnot gas refrigeration or heat pump cycle. Assuming the ideal gas model for the air, determine: (a) the magnitude of the net work input, in kJ per kg of air, and (b) the pressure at the end of the isothermal expansion, in kPa.
A refrigerator operates according to a Brayton cycle, diagrammed below. The gas conditions (gamma=1.4) at point 1 are P1,V1 and T1=100K. It is known that V1 =10V2=5V3=V4/2.Consider that Tf is the temperature of the cold source and Tq is the temperature of the hot source. It is known that Tq and Tf are, respectively, the maximum and minimum possible for the refrigerator to operate under these conditions. reservoirs would have a coefficient of performance closer to:
Please help me out. Thermodynamics. Thank you.
Shown in the figure below is the cycle undergone by a Heat Pump. Your heat pump runs using 38.55 moles of monatomic Helium gas. At point a in the figure, the temperature is T₂ = 321 Kelvin and the pressure is Pa = 216000 Pascals. During the process a→b, the Volume of the system Quadruples. P Cv= Cp Y = C с a STATE a b isothermal P (Pa) b V Joules/(mole. K); Joules/(mole K); V (m³) T (K) PROCESS W (J) a-b b-c c-a Total Qhot = Qcold = Performance Coefficient = Joules; Joules; Q (J) AU (J) Activate Windows Go to Settings to activate Window
Derive the seven general property equation of the following thermodynamics processes: a. POLYTROPIC PROCESS
Derive the 7 general property equation of the following thermodynamics processes: a. ISOMETRIC PROCESS
Q: The working fluid, in a steady flow process flows at a rate of 220 kg/min. The fluid rejects 100 kJ/s passing through the system. The conditions of the fluid at inlet and outlet are given as : C1 = 320 m/s, p1 = 6.0 bar, u1 = 2000 kJ/kg, v1 = 0.36 m3/kg and C2 = 140 m/s, p2 1.2 bar, u2 = 1400 kJ/kg, v2 = 1.3 m3/kg. The suffix 1 indicates the condition at inlet and 2 indicates at outlet of the system. Determine the power capacity of the system in MW. The change in potential energy may be neglected. Fluid Fluid leaves System enters
Do complete problem with all parts
The manufacturer of the device claims that it accepts a heat transfer at a rate of QH = 3.0 kW from a low-grade source of geothermal heat at TH = 80ºC and rejects heat at rate QC to the atmosphere at TC = 20ºC. The device operates at steady state and produced work at a rate of W= 2.5 kW. There are no other heat or work transfers from the device. a.) What is the rate at which the device rejects heat to the atmosphere, QC ? b.) Is this device possible? Justify your answer using an entropy balance.
1- A fluid at 0.7 bar occupying 0.09 m' is compressed reversibly to a pressure of 3.5 bar according to a law pv" = constant. The fluid is heated reversibly at constant volume until the pressure is 4 bar; the specific volume is then 0.5 m/kg. A reversible expansion according to a law pv = constant restores the fluid to its initial state. Sketch the cycle on a p- v diagram and calculate: a- the mass of fluid present; b- the value of n in the fist process; c- the net work done of the cycle.
A refrigeration machine rejects QH = 680 Btu per cycle to a hot reservoir at TH = 540°R, while receiving Qc = 483.0 Btu per cycle from a cold reservoir at temperature Tc. The machine operates at 10 cycles per minute. Determine the net power input, in hp, the minimum theoretical temperature Tc, in °R, and the maximum coefficient of performance of the cycle. tep 1 Determine the net power input, in hp. W cycle i hp

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A working fluid in a closed loop undergoes the following cycle: • 1-2 Isentropic compression • 2-3 Isobaric heat addition • 3-4 Isentropic expansion • 4-1 Isobaric heat rejection Identify the temperature-entropy (T-s) diagram that illustrates this cycle. T 2 2 3 3 4 S 1 4 4 2 3 3 4 S