A work piece diameter is 30mm has been reduced to 27mm in turning process.Therefore one of the following is correct.A. The depth of cut is 1.5mmB. The feed rate is 3mm.15.C. The feed rate is 1.5mm.D. The depth of cut is 3mm16.Facing operation is performed on?A. Drilling machine.B. Sawing machine.C. Milling machine.D. Lathe machine.17.The manufacturing process of removing material from the work piece is called.A. Milting and casting process.B. Machining process.C. Forming process.D. Extrusion processSpot welding is classified as:A. Thermit WeldingB. resistance weldingC. Friction weldingD. Arc WeldingTimber is the name given toa. Marking tool.b. SteelC. Glassd.18.19.WoodThe manufacturing process shown in the figure below is called?A. Spinning process.B. Turning process.C. Machining process.D. Bending process.20.

We are authorized to answer one question at a time, since you have not mentioned which question you…

A work piece diameter is 30mm has been reduced to 27mm in turning process. Therefore one of the following is correct. A. The depth of cut is 1.5mm B. The feed rate is 3mm. 15. C. The feed rate is 1.5mm. D. The depth of cut is 3mm

A work piece diameter is 30mm has been reduced to 27mm in turning process. Therefore one of the following is correct. A. The depth of cut is 1.5mm B. The feed rate is 3mm. 15. C. The feed rate is 1.5mm. D. The depth of cut is 3mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

14. Determine the proper RPM for a 3" piece of cold-rolled steel with a cutting speed of SFPM. Round the nearest RPM. Hint: Refer to formulas and examples in your textb а. 102 b. 115 C. 87 d. 146 15. Calculate the machining time (in minutes, rounded to the nearest minute) for a part in length 10" diameter AISI/SAE 4140 steel using a cutting speed of 110 SFPM and a rate of 0.008 IPR. Hint: Refer to examples in your textbook. а. 47 b. 60 C. 86 d. 74
What is the feed speed (mm/min) of an end milling cutter if it mills a distance of 300 mm in ten minutes? What is the feed per tooth if it is rotating at 800 rpm?
What part of the lathe is used to set the feed rate of the cutting tool?
9) Down milling operation is performed for finishing cut. Select one: True False
Orthogonal cutting is dimensional metal cutting a. two b. one Four d. Three
1.) On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The cutting speed is _________?(m/min)
Marking tool. 10. The manufacturing process shown in the figure below is calledr a. Turning process. b. Spinning process. C. Machining process. d. Bending process. USF alell äis l 11. The operation wnere enlarging a hole is called Drilling b. Tapering. Reaming Boring. a. C. d. thư one nf the following.
A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…
10. The manufacturing process shown in the figure below is called? ng tool. .. a. Turning process. b. Spinning process. c. Machining process. d. Bending process. 11. The operation wnere eniarging a hole is called a. Drilling b. Tapering Reaming Boring. С. d. is ohtained by one of the following.
Fill in the data needed in the table RPM FEED LENGTH OF CUT CUTTING TIME 325 0.006 6. 6 1/8 74 0.010 2 7/8 130 0.008 1 1/2
How long will it take to saw a rectangular piece of aluminum plate 8 inches wide and 1.5 inch thick if the length of the cut is 8 inches, the power hacksaw makes 120 rev/min and average feed per stroke is 0.0060 inch?
formula is used to find the cutting speed. a. rpm b. tana =(d1 -d2)/2L c. m/min d. (dl – d2) / 2 mm