A wooden column with modulus of elasticity of 136280 N/mm´ is hinged at one end and fixed at the other end If the total length of the column is 375 cm, width of the column is 35 mm and depth is 30 mm. What is the effective length Le in mm & buckling load P in kN?

A wooden column with modulus of elasticity of 136280 N/mm´ is hinged at one end and fixed at the other end If the total length of the column is 375 cm, width of the column is 35 mm and depth is 30 mm. What is the effective length Le in mm & buckling load P in kN?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A simply supported beam has a height of 600 mm and a width of 300mm. Determine the maximum safe live…

Q: Given below is the properties of HP 410 x 131 steel column having a length of 10 m and fixed at both…

A: Consider the given data. The column is fixed at both ends, KL=0.5×10000=5000 mm

Q: A cantilever beam as shown below has a rectangular cross section of b=200mm, d=390mm, span=2.4m with…

A: Given:- b=200mmd=390 mmspan = 2.4mNo of bars = 2diameter of bars =22mmdead load = 12kN/mLive load =…

Q: Sign 700 mm = 300 mm

Q: A simply supported beam shown below is HEA 400 of 5355 steel. It is laterally supported at points…

A: Since the beam is symmetrically loaded we get Maximum Bending Moment at the Midspan.Maximum bending…

Q: A timber column, 8 in. by 8 in. in cross section, is reinforced on all four sides by steel plates,…

Q: A 1016 mm P 25 mm 330 mm 25 mm 254 mm A 12.5 mm

A: Lets Draw SFD and BMD in terms of P value M=-P×1.016 kNmV=P kN

Q: raw shear force and bending momentdiagram for beam below 100 KN/m M = 1200 kN.m %3D A 2 m 4 m Im' 1m

Q: Question 3 Part a: For the section shown, determine the: • Maximum elastic Moment M Fully plastic…

A: Given Dataσy=250 MN/m2E=200 GN/m2We are supposed to calculate the following parameters.Maximum…

Q: Example: A reinforced concrete slab is to be composed of several panals as shown below. Beams of…

Q: A wide flange A60 steel column has a length of 5.8meters and pinned ends. If Sx=857x103 mm3,…

A: The following are the given information. A=7243 mm2 Fy=414 MPa Sx=857×103 mm3 Sy=135×103 mm3 d=358…

Q: An ASTM A36 (Fy=36ksi) wide flange column has a length of 16feet and fixed ends. If rx=4.64in,…

Q: An A36 WF steel column has a design compressive strength of 159.6kilo pounds. If LL=2.9DL, calculate…

Q: Identical steel bars are used to support a 7400-N load as shown. For the properties of steel bar: A…

Q: 13/13 FOR THE RIGID BEAM SHOWN BELOW FIND THE STRESS IN ALUMNUM ROD Steel Rod Est= 200 kN/mm A…

Q: A column in the upper story of a building is subjected to a compressive load from the following…

A: D = 308 kNL = 170 kNLr = 187 kNW = 197 kN To determine:a) factored loadb) Required design strength…

Q: The compression member, 8 m long, pinned at both ends has additional support in the weak direction…

A: GIVEN DEAD LOAD = 575 KN LIVE LOAD = 1000KN TOTAL LOAD = 1000+575 =1575 KN (1k= 4.44 kN) = 354.07 k…

Q: A cast iron 3m long is completely filled with concrete and used as vertical strut. If the external…

A: It is required to determine the stress in cast iron. We know that stress in cast iron is equal to…

Q: A timber beam shown in the figure is made up of Sasalit (50% stress grade). Use LRFD. All thegiven…

Q: A cantilever beam of 7.2 m span is a part of a floor supporting a concrete hollow block partition.…

A: Deflection : The degree to which a component of a structural member is shifted under a load is known…

Q: 3m 200 ………… h B 6kN/m t

Q: The beam is loaded as shown. which of the following nearly gives the flexural stress du to tension…

A: Find the reactions :RA=RB=12×4+2×12×12×42=48kNMax moment will be at the midspan…

Q: A steel column of rectangular section 5 mm * 2mm and length 2 m is simply supported at both ends.…

Q: A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

Q: Design the steel reinforcement for flexure for the beam to carry the loads shown in the figure…

Q: Q3) Consider the rectangular reinforced concrete section given below. Calculate the moment capacity…

A: Width of beam, b = 300 mm Total depth, D = 600 mm Effective depth, d' = 35 mm Effective cover, d…

Q: Design the steel reinforcement for flexure for the rectangular tapered beam to carry the loads shown…

A: Live load, LL = 20 kN/mcover = 75 mmwidth, b = 380 mmHeight at the fixed end, hf = 800 mmHeight at…

Q: Question 1 [Soalan 1] Members AB and AC support the 100 kg crate. Determine the tensile force…

Q: Determine the maximum allowable internal moment M that can be applied to the beam. Express your…

Q: The crate weight is 250 lbs and the coefficient of static friction is us - 0.4. Find the maximum…

A: Given : Crate weight = 250 lbs Coefficient of static friction is = 0.4 To Find : The maximum force…

Q: Design Shear ReinForcement For a beam Shown below. It's Si ze is 350 x 600· It's effective dep th…

A: Data given: Length of the beam (L) = 6.3 m Uniformly distributed load (w) = 130 kN/m Size of the…

Q: 1. Rope AB and AC are both made from DupontTM Kevlar 29 brand fibers. The cross-sectional areas and…

A: Cross sectional area of wire AB, Length of wire AB, Cross sectional area of wire AC, Length of wire…

Q: For the cantilever beam(300x700mm) to carried the loads shown in the figure below, calculate the…

A: Cantilever beams are not flexible structural elements that are supported at one end and loose at the…

Q: 1. A square timber column, 10 in by 10 in in cross section, is reinforced on all plates, each plate…

Q: An aluminum strut 6 ft long has a rectangular section 0.75 inch by 2 inch. A bolt through each end…

A: GIVEN- Factor of Safety=1.75 Young's modulus (E)=10×106psi BOTH END HINGED- EFFECTIVE LENGTHle…

Q: A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown…

A: (a)Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type…

Q: 13/13 FOR THE RIGID BEAM SHOWN BELOW FIND THE STRESS IN STEEL ROD. Ast3 200 mm2, Aalu=300 mm2 Steel…

Q: Question 3 Please determine the number of Degree of Freedoms (DOFs) of the structures in below when…

A: Degree of freedom is defined as minimum numbers of independent variables required to define the…

Q: 1) AW 10 x 100 compression member is pinned at both ends. Its properties are weight per linear meter…

A: Answer Let us first check for local stability of given Compression member for slender and non…

Q: PDL = 5 KN 500 mm Wp =6 KN/m WL = 3 KN/m. PLL = 3 KN 800 mm R1 R: 2 m 1m

Q: Refer to the figure shown. Given a W8x48 A992 steel with 2-49 in, which of the following statements…

Question

100%

A wooden column with modulus of elasticity of 136280 N/mm is hinged at one end and fixed at the other end.
If the total length of the column is 375 cm, width of the column is 35 mm and depth is 30 mm. What is the
effective length Le in mm & buckling load P in kN?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Solution

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A square timber column, 10 in by 10 in in cross section, is reinforced on all four sides by copper plates, each plate being 10 in wide and "t" in thick. Determine the smallest value of "t" for which the column can support an axial load of 560 kips if the working stresses are 1250 psi for timber and 17 ksi for copper. The moduli of elasticity are 1.5 x 10°psi for timber and 17 x 10 psi for copper.
A wide flange A60 steel column has a length of 6.4meters and pinned ends. If Sx=888x103 mm3, Sy=128x103 mm3, d=358mm, bf=184mm, A=7,289mm2, Fy=414MPa, calculate the critical buckling stress, Fcr in MPa of the column. Express your answer in one decimal place.
i need the answer quickly
A 210 kN axial compressive load is applied to a W530x101-steel column with the length of 3.20 m and cross sectional area of 12900mm2. The modulus of elasticity of this steel is 203 GPa. a) Find the stress acting on the column. b) Find the length change of the column under this load. For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac). BIUS Paragraph Arial 14px A v
What is the C or T, the X and Y components and the load of each member. Also can you put the answer like it is on the image.
can someone please help me with this? Thank you -) A short square steel structural tube is used as a compression member and is subjected to an axial load.Axial deformation is 0.004 inches. What is the load?
Calculate the available strength of the W360  179 column with unbraced lengths of 9 m in both axes. The material properties and loads are given below. The column is verified for ASTM A992 (Fy= 345 MPa) material. W360 x 179Ag = 22,800 mm2rx = 158 mmry = 95 mm
I need the answer to the question in reinforced concrete
Q1- A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1. Using Working Stress Method to calculate maximum load (Pmax.) which act at the mid-span of the beam (neglect self-weight), 100 mm 100 mm -537 mm- 40 25 mm 300 mm -ww009 Figure 1 Pmax L=5 m-
Can you solve number two
Homework 3: Q1/ The beam shown in figure below consists from steel and aluminum, find the maximum load that can be applied if the stress in steel not exceeding 80MPA and in and Aluminum 3OMPA. Es = 210GPA EAlu = 70GPA 3PKN/m Steel 40mm 220mm Aluminum 6m Steel 40mm 100mm
The cantilever beam shown below has the cross-section on the right portion. If the allowable stresses are 62 MPa shear and 103 MPa tension at point A (just below the flange), determine the maximum allowable load P.