A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 KN as shown.50mmA.30500 mm150 kNDetermine the total tensile stress at ASelect the correct response32.48 MPaO29.98 MPaO52 46 MPa34 98 MPa

Answered: Image /qna-images/answer/af256749-10be-4c3b-b633-1273941ffa28.jpg

Answered: A wooden beam whose length is 1 m is…

A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 kN as shown. 50 mm A. 30% 500 mm 150 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 10 m simply supported beam with uniform load of 3 kN/m from right end to left end has a maximum…

Q: A cantilever beam is 2 m long supports load of 1000N/m over of its entire length. The beam is 100 mm…

Q: if 1000 lbs is applied at Point A. What is the applied gravity load at point B? What is force Ph?…

A: GRAVITY LOAD is a load or force in which gravity is involved with some mass and gravity is applied…

Q: A simple uniformly distributed 20 ft. beam carrying a load of 1000 lb./ft. is simply supported at…

Q: Calculate the support reaction forces of the simple beam given its dimensions and loading condition.

Q: Calculate the load that will make point A move to the left by 6mm, E-228GPa. The diameters of the…

Q: A cantilever beam of length L = 16 ft is loaded with three forces as shown. For a = 1 ft, b = 2 ft,…

Q: Find the bending stvess at point B located at stress at Im from the right end of the beam. 2 Nlm…

A: Given:

Q: THE LOAD SAFELY OR NOT O =1024 KG/CM? 18 T 90cm 20 cm 36 cm + 4 m. 5 m. 20 cm

A: Bending stress When some load is subjected to the beam then shear stress and bending moment act on…

Q: 0 m simply supported beam with 25 kN load 3 m from the left end a maximum slope at the left end: (IE…

A: Given data Length of beam = 10m Load = 25kN at 3m from the left end IE = 8000(kN-m2) Find the…

Q: 1. A simply supported beam is subjected to loadings as shown. Use E = 10 x 10° N/m2 and / = 20 x 106…

A: Consider vertically upward & horizontally forward force as (+)ve and vertically downward &…

Q: A mild steel bar 60mm in diameter is simply supported and has a span of 2m. What load suspended at…

A: Given, Diameter of bar = d = 60 mm = 0.06 mLength of bar = l = 2 mTotal deflection = δ = 8 mm =…

Q: A proving ring is 25 cm mean diameter, 4 cm wide and 6 mm thick. The maximum stress permitted is 550…

A: A providing ring has a diameter of 25 cm, a width of 4 cm, and a thickness of 6 cm.The greatest…

Q: Refer to the beam loaded as shown. What is the value of Ay? y 8.2 m - 5.5 m - 1000 N 600 N 4.5 m…

Q: Find the internal loading at point C. 30 kN - m 10 KN A- 5 m-1.5m-1.5 m-1.5 m- B .

A: Given data:- applied load =10kN applied moment =30kN-m Length of the beam =6 m To find:- Internal…

Q: The material has a specific weight y= 61 lb/ft (Eigure 1) Figure K 1 of 1> 0.25 t 0.25 ft 2 ft 0.5…

A: Given data: γ=61 lb/ft3 Need to determine the moment of inertia of the wheel about an axis which is…

Q: Our University wants to construct a swimming pool inside the campus, for which they are in need of a…

Q: 0.3m 40 KN Icm 5cm 7cm 0.5m 5cm Icm 10 kNm 0.2m Find deflection of the beam at the point where 40kN…

A: Here are reaction forces at pin support A and is reaction force at roller support D.At…

Q: Considering only pure bending, determine the minimum section modulus for the component and loads…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: Esteel=20Ewood- Owood = 10 MPa. OSteel= 150 MPa wood Steel \00 mm

Q: E= 29000ksi I=291 in4 6 ft Add your answer B Determine the deflection of the beam at midspan. Answer…

Q: A W shape is to be used for a uniformly loaded simple beam carrying a total dead load of 27 kips and…

A: Given:

Q: What is the tensile strength? Given: Material: aluminum Beam length: 9.75in Beam width: .4155in…

A: Given data as per question

Q: A 30 cm X 16 cm rolled steel joist of I-section has flanges 11 mm thick and web 8 mm thick. Find the…

A: Given that, I-section,Width of flange=30 cmHeight of web=16 cm,Thickness of flange=11 mm,Thickness…

Q: An 8 m simply supported beam has a uniform load of 2 kN/m from left end to right end and…

Q: QUESTION 2: 2.1 What is the critical load for a rectangular section bar 40 mm by 50 mm and length…

Q: Choose correct answer: Load treated to be acting at a point in a beam is called Uniformly…

A: Uniformly varying load: Uniformly varying load is a type of loading in which the magnitude of the…

Q: Q1. For the beam given below, find the equation for deflection along the beam. L P EI = GIVEN USE…

Q: A cantilever beam, 850 mm long, carries a uniform load of 5 kN/m. What is the value of Ely at the…

A: GIven: Cantilever beam w=5 kN/m L=850 mm TO determine: EIy at free end

Q: A simple two-bar mechanism supports a 500-lb Determine the internal re- load as shown in Fig.…

A: The simpler representation of the given figure is shown below We take the necessary dimensions from…

Q: Don't use chatgpt. Only handwritten solution.

A: Note: I hope it helps. Thank you.

Q: 14.14KN 20KN 40KN-M C20KN/M 1M

A: Shear force diagram represents shear force at every section of the beam. Shear force at any…

Q: A 19 ft long, simply supported beam is subjected to a 5 kip/ft uniform distributed load over its…

A: Here, Length of the beam = L = 19 ft = 228 in Uniform loading = w = 5 kip/ft = 0.4167 kip/in = 416.7…

Q: 2. Design a timber beam (S4S) made of Douglas fir to support the load shown below.

Q: A beam of span 3 m is subjected to an udl of 2.5 N/m, when converted to a Point load is equal to…

A: A beam of span 3 m is subjected to an udl of 2.5 N/m, when converted to a Point load is equal to a.…

Q: Find the shaft diameter in Fig. 2 if the allowable deflection is 1 mm. The values for F 60 KN, and…

A: F = 60 kN Allowable deflection = 1 mm Assume E = 210 Gpa

Q: For the beam shown with El is constant, what is the deflection of A? 26.25 kN-m A 10 kN/m 3 m B 1 m

Q: A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 20.7 MPa and fy…

A: f'c=20.7 MPafy=415 MPaϕ=0.9Wself=29.54 kN/m3assume…

Q: uestion Precision Engineering Contractors was awarded a government contract to construct a bridge…

A: The ABC beam is simply supported beam The distributed load between A and B is The concentrated load…

Q: For the beam shown in Fig. Determine the value of the mm distributed load W if the maximum shear…

A: Given beam

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 KN as shown.
50
mm
A.
30
500 mm
150 kN
Determine the total tensile stress at A
Select the correct response
32.48 MPa
O29.98 MPa
O52 46 MPa
34 98 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 4 What is the equivalent concentrated load of a triangular load which varies from 0 at one support and 9 kN/m at the other support carried by a 6-m simply supported beam? (Answer must be in kN.)
شمدنسحب
Two columns (circular and square) of same lengths have same cross-sectional areas of A and made of same materials. What is the ratio for the critical loads if they are both simply supported (One end fixed other end pinned) ?
5) Compute the value of EI y at the right end of the overhanging beam shown. 1000 lb 400 Ib/ft to 6 ft 4 ft * 3 ft → R1 R2
Draw sfd and bmd of the given beam please handwritten only I'm again warning only handwritten and correct with explanation
diagrams för the modıfied loading. What is the [6.67, - 3.33, 1.67, - 13.33 kN; 2.67, 2, 2.67 kN m. 3.3 (A). A cantilever beam AB, 2.5 m long is rigidly built in at A and carries vertical concentrated loads of 8 kN at B and 12 kN at C, 1 m from A. Draw S.F. and B.M. diagrams for the beam inserting princtpal values. [-8, - 20 kN; -11.2, -31.2 kNm.]
STRENGTH OF MATERIALS
1 A 19 ft long, simply supported beam is subjected to a 5 kip/ft uniform distributed load over its length and 11 kip point load at its center. If the beam is made of a W14x30, what is the deflection at the center of the beam in inches? The quiz uses Esteel = 29,000,000 psi. Ignore self-weight.
Do not give answer in image and hand writing
Please include free body diagram. The answer must be in Handwritten format.
Figure 14.20 Full Alternative Text 14.21 A solid rectangular simply supported timber beam 6 in. wide, 20 in. deep, and 10 ft long carries a concentrated load of 16,000 lb at midspan. Use nominal dimensions. a. Compute the maximum horizontal shear stress at the neutral axis. b. Compute the shear stress 4 in. and 8 in. above and below the neutral axis. Neglect the weight of the beam.
Calculate the bending moment for the fire design in the center of 5 m span if the strip of slab is 1 m wide. The factored load for fire design is 4.2 kN/m2. Select one: O a. 13.12 kNm O b. 12.75 kNm O c. 8.14 kNm Od. 15.86 kNm