Esteel=20Ewood- Owood = 10 MPa. OSteel= 150 MPa wood Steel \00 mm

Q: 21-B // A steel bar has a square section of 10 mm side and a length of 60 mm, subjected to a tension…

A:

Q: Problem 2: The short cylindrical block of 2014-T6 aluminum, having an original diameter of 0.5 in.…

A: Given:d=0.5 inL=1.5 inP=800 lbE=10.6*106 Psiμ=0.35

Q: Two objects are connected by a light string passing over a light, frictionless pulley as shown in…

A: Given Data, m1 = 7 Kg m2 = 3 Kg Height, h =2.6 m To find :- a) Speed of mass, m2 just as mass m1…

Q: Strain of Silly Putty: Initial length (L0): 2.85 cm Final length (L): 8.50 cm Strain: % (show…

A: Initial length (): 2.85 cmFinal length (L): 8.50 cm

Q: UT FOR CONCENTRIC 回SS, Fy (MPa) 0 5-222 222 32 S 寸 246 288 288 244 287 286 19739 241 284 282 322 074…

A:

Q: b) Determine the smallest value of ho

A: Solution : we have  load w= wocosπx2L Relation between load & shear  dVdx=…

Q: The is a rope that just cannot stretch more than 0.6 cm from a tensile force of 500N without…

A: Given: Tensile force applied on the rope, T=500 N mass of the rope, m=0.5 kg length of the rope,…

Q: 10 A pulse is sent from a ship to the floor of the ocean 420 m below the ship; 0.60 s later the…

A:

Q: Q1: Find a relation between true strain () and reduction in area (r)?

A:

Q: find shear and Binding monont dkagr 5KN/m 3m 5m ThT 3m

A:

Q: Given data: Stress-35 MPa Modulus of elasticity=78 MPa Find strain

A: Find the strain. Using hook's law.

Q: Data: P = 2 kip d = 3.6 inch w = 305 millimeters t = 0.03 meter r = 5.08 centimeter h = 0.6667 feet…

A:

Q: The rigid bar AB as shown in Figure Q1(a) is supported by a steel road AC having a diameter of 22 mm…

A:

Q: The Ultimate strength of the material * is

A: Basics of Stress-strain diagram.

Q: Emate =315 mPA G 28GPA Cmad ulus rigidi- -130 mPA nate= 185 mPA Elculate Poisson's Patio fwe have a…

A:

Q: A glass consists of cracks at surface and interior side. The surface crack lengths are s 5 µm, the…

A:

Q: shows the state of stress at a critical point on a component of a lawn mower, wh Opx = 10 MPa…

A: Givenσxx=10Mpacompressive=-10Mpaσyy=25Mpatensileζxy=90Mpacloclwiseσzz=20MpacompressiveSyt=300MpaSyc=…

Q: Problem 1: For a 20-ply lay-up [(0/90)s]s in which ply thickness is 0.1 mm and stiffness is: 20. 0.7…

A: Solution:   Given Data:

Q: a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed stress = applied…

A: As this is a simple question related to the strength of material subject. As stress formula is given…

Q: A tianium disk (roe 107 CPa, Poisson's ratio = 0,34) precisely 8 mm thick by 30 mm diameter is used…

A:

Q: stress 6 Q/Interpret the following drawing soft plastic fiber hard plastic elastomer strain (8)

A:

Q: Write the Shear strain max formula for Torsion?

A: To calculate the maximum shear strain value for torsion we must take into account the torsion…

Q: 27c) The Vickers hardness value of a material is 526.58 HV. What is its mean diagonal if the applied…

A: Given data: Hardness value HV=526.58 Applied load F=30 kgf Angle between edges θ=136°

Q: FIND: MODULUS OF ELASTICITY

A: Given tabulation values  to FIND: MODULUS OF ELASTICITY

Q: Problem 6.11 Compute the [A], [B], and [D] matrices for a one-lamina [30] laminate 142 GPa, with…

A: GivenMatrics for a one-lamina 30 G12=7.2Gpat=1.0mmE1=142GpaE2=10.3Gpaν12=0.27ν23=0.38

Q: FIND: MODULUS OF RESILIENCE

A: FIND: MODULUS OF RESILIENCE

Q: ABC triangle is drawn on the thin plate in the figure when it is unloaded. AB length is parallel to…

A: Given:To find:

Q: TOPIC: ELASTICITY A load of 50 kg is applied to the lower end of a steel rod 80 cm long and 0.60 cm…

A:

Q: 14. A bar of 2 m length, 20 mm breadth and 15 mm thickness is subjected to a tensile load of 30 kN.…

A: Given:- length: 2m breadth: 20mm thickness: 15 mm Load 30 KN

Q: If a bar is subject to a compressive force of 15 lb, and the area of the bar is 0.1 in^2 (square…

A:

Q: Sketch the stress / strain relationship for steel bar element

A: Sketching the stress /strain relationship for steel bar elements.

Q: Two of the stress components in a 2-D plane stress system are found to be: = 5.0 MPa. бy It has also…

A: Given data: (a) Principal Plane: it is the plane that consists only of normal stress, the value of…

Q: stress 37 ksi- strain in 0.002- in

A: In the given question did not mention clearly what is found... Young Modulus of elasticity,E is…

Q: Example 2: Locate the centroid of the area under the curve x = ky from x = 0 to x = a. Giving that k…

A: Draw a diagram considering a horizontal strip of thickness dy at a distance y from the x-axis.…

Q: the change in length and Calculate the change in diameter.

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.