A wire of length 3 m and diameter 0.3 mm is stretched by hanging a weight of 2 kg from it and the elongation produced is 2 mm. Calculate the Young's modulus and the strain potential energy of the wire.
Q: A bending moment of 262 Nm is applied to a solid bone with a radius of 1.9 cm. Calculate the bending…
A: Given data: Bending moment, M=262 Nm Radius of the solid bone, r=1.9 cm=1.9×10-2 m Distance from…
Q: A bending moment of 160 Nm applied to a hollow bone (outside radius = 2.5 cm; inside radius = 1.9…
A: Given: Bending moment M=160Nm Bending stress σ=16.7×106 N/m2 Outside radius, 2.5 cm= To find: Radius…
Q: Two wires have diameters in the ratio 1 : 2, lengths in the ratio 3 : 4 and Young's moduli in the…
A: To find-Ratio of elongations producedGiven-Diameters of two wires are inn the ratio,D1D2=12
Q: A load 1 kg produces a certain extension in the wire of length 3 m and radius 5 x 10-4 m. How much…
A: To find- Lateral strain=? Given- Load (M)=1 kgLength of wire (L)=3 mRadius (r)=5×10-4mYoung's…
Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…
A: Given Elongation of the bar between A dan C δtotal = 0.22 in Strain ε2…
Q: Bulk modulus is defined as -P / (ΔV/V). Therefore it can be negative. True or False? a) True b)…
A: The Answer is False.
Q: A control rod made of yellow brass must not stretch more than 3 mm when the tension in the wire is 4…
A: Solution:-Given thatDeformation in control rod (δ)=3 mmTension in the wire (T)=4 kN=4×103 NYoung's…
Q: The yield strength of a person’s ACL is approximately 3.5x10^7 N/m^2. What is this persons Modulus…
A:
Q: Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The…
A: ANSWER :- As in question normal stress is asked and can be calculated as force/area. Area of rod 1…
Q: Find the longitudinal stress to be applied to wire to decrease it's Liameter uniforenly by 10%…
A: We need to compute-Longitudinal stress =?The data given as-Lateral strain=10%=110Poisson's ratio…
Q: A copper wire of length 6.7 m , cross sectional area 3.2 x 10--m²and Young's modulus 11 x 1010 N/m²…
A: Length of wire L = 6.7 m Cross-sectional area A = 3.2 × 10- 6 m2 Young modulus Y = 11 × 1010 N/m2…
Q: Two parallel and opposing forces of each value (4000N) act tangentially on opposite sides of a cube…
A: Given: Force F=4000 N Side length L=25 cm=25×10-2 m Shear modulus S=80 GPa=80×109 Pa
Q: A 3 m long copper wire is stretched to produce an extension of 0.3 cm. If Poisson's ratio for copper…
A: We have to find the lateral strain produced. We know that, Length of wire (L) is 3 m, Elongation…
Q: Explain the tem bulk modulus.
A: The bulk modulus is defined as a constant that describes how resistant a substance is to stress. It…
Q: I have a square box with a notch in the center, this one has two modes: 0 and 45 degree angle. A…
A:
Q: Max (mass = 15 kg) is hanging from one end of a 13-m long bungee cord that has its other end fixed…
A:
Q: A 73 m length with a radius of 2.3 m of a cylinder supports a 9.5 x 10 5 kg mass which presses down…
A:
Q: • A steel wire of diameter 1 x 10³ m is stretched by a force of 20 N. Calculate the. strain energy…
A: We need to compute-Strain energy per unit volume=?The data given as-Diameter of wire (d)=10-3 mForce…
Q: A copper metal cube has each side of length 1m. The bottom edge of cube is fixed and tangential…
A: We have to find Lateral displacement (x) Given: Length of each side is 1 m Tangential force (F) is…
Q: A 350 mm diameter solid steel drive shaft transmits 4500 kW at 120 rpm to a hollow steel shaft via a…
A: Given,Drive shaft diameter (D) = 350 mm Transmitted power (P) = 4500 kW Rotational speed (N) = 120…
Q: A 7-kip · ft torque is applied to a hollow aluminum shaft having the cross section shown. Neglecting…
A: Given data- T=7 kip-ft Radius of outer circle, r0=7 in Radius of inner circle, ri=14 in-4 in-2 in2=4…
Q: The 100-kg uniform rectangular plate is supported by an ideal pivot at O and a spring which must be…
A:
Q: A load 1kg produces a certain extension in the wire of length 3m and radius 5x10-*m. How much will…
A: We need to compute the lateral strain produce in the wire.The data that has been provided is-Load…
Q: Tensile load of 2 MN is applied to an Aluminium cord with original diameter of 5 mm, the measured…
A: Given data: Magnitude of tensile load is, F=2 MN=2×106 N Original diameter of Aluminum cord is, d=5…
Q: The five-bolt connection must support an applied load of P-4700 lb. If the average shear stress in…
A: Given that - Five bolt connection Applied load(p)= 4700lb Averge shear stress in the bolt must be…
Q: R [6r – (4)a a Find the maximum velocity for the velocity profile shown here (an expression based on…
A:
Q: A system requires a metal component with the design specification that it not experience more than…
A: Given data: The stain is ε=0.1%=1×10-3 The range of the stress is σ=0,1000 kPa First, calculate…
Q: las Sura
A: Given: Length of cylindrical specimen is 200 mm Diameter is 10.7 mm Force is 50,000 N Diameter is…
Q: . Strain energy of the stretched wire is 18 × 10-³ J and strain energy per unit volume of the same…
A: We need to compute-Volume of wire (V)=?The data given as-Strain energy per unit volume=6×10-3…
Q: Consider an aluminum rod of radius r = 1.5 cm subjected to a uniaxial tension test by force of F =…
A:
Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…
A:
Q: Assuming that the youngs modulus of spider ilk is 8.4x10^9 pascals. If the spider silk a radius of…
A:
Q: If a wire having initial diameter of 2 mm produced the longitudinal strain of 0.1 %, than the final…
A: To find-Final diameter=?Given-InitIal diameter (D)=2 mmLongitudinal strain…
Q: If you bend a rod down, it compresses the lower side of the rod and stretches the top, resulting in…
A: The given relation for the restoring force is
Q: of length 05 mm2 15.
A: Given as, L= 2m, A= 0.5x10-6m2, I= 2x10-3m, F=5x9.8N.
Q: One end of a copper rod with a diameter of 20 mm and a length of 0.95 m is held in a vise. A force…
A:
Q: As illustrated in the figure, consider a circular cylindrical rod tested in a uniaxial tension test.…
A:
Step by step
Solved in 3 steps
