As illustrated in the figure, consider a circular cylindrical rodtested in a uniaxial tension test. Two points A and B located at adistance lo = 32 cm from each other are marked on the rod, and atensile force of F = 980 N is applied on the rod. If the tensile strain andtensile stress generated in the rod were ε = 0.06 cm/cm and σ =MPa, determine:(a) The radius, r, of the rod after the application of the force2.2(b) The total elongation of the rod, Al, after the application of the forceABF©

Answered: Image /qna-images/answer/d07cb9c5-1c89-4332-8602-202da53cb2d0.jpg

Answered: As illustrated in the figure, consider…

Similar questions

the drawing shows a 150 kg crate hanging from one end of steel bar (S= 8.1 x10^10 n/m^2) The length of the bar is 0.428 m and its cross-sectional area is 7.94 x 10 ^-4 m^2. Neglect the weight of the bar itself and determine (a) the shear stress on the bar and (b) the vertical deflection deltaY of the right end of the bar.
Gold, which has a density of 19.32 g/cm3, is the most ductile metal and can be pressed into a thin leaf or drawn out into a long fiber. (b) If, instead, the gold is drawn out into a cylindrical fiber of radius 2.100 μm, what is the length of the fiber?
A 330 gram ball is attached to one end of a rubber (Young's Modulus= 0.120 GN/m²) wire of diameter 1.32 mm and an unstretched length of 83.0 cm. The other end of the wire is attached to the top of a post. The ball rotates around the post in a horizontal plane such that the angle between the wire and the horizontal is 10.5 degrees. Find the tension in the wire and the increase in the wire's length due to the tension in the wire. Tension = ALength cm
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
A 1.25 m long cable has a diameter 3.50 mm with a Young’s Modulus, E, of 9.75 x 109 N/m2 . When the wire is placed under tension, it experiences a stress of 202.52 x 106 N/m2 , the length of the cable extends by 36.35 mm. Calculate the force that the cable experiences under tension and the strain energy density (U/V) due to deformation. Give your answers in newtons (N) to 2 decimal places for the force; and in joules per cubic metre (J/m3 ) for the strain energy density to 2 decimal places. Assume the cable is solid and the material is homogeneous.
A satellite similar to the Tethered Satellite in the figure below has a mass of 550 kg and is at the end of a 19.2 km long, 2.90 mm diameter cable with the tensile strength of steel. (a)How much does the cable stretch (in m) if a 108 N force is exerted to pull the satellite in? (Assume the satellite and shuttle are at the same altitude above the Earth. Young's modulus for steel is 210 ✕ 109 N/m2.) m (b)What is the effective force constant of the cable (in N/m)? N/m (c)How much energy (in J) is stored in it when stretched by the 108 N force? J
The muscle fibers in muscle A have a pinnation angle of 25 degrees, while the muscle fibers in muscle B have a pinnation angle of 20 degrees.Two pennate muscles have the same cross sectional area and produce the same tensile stress. Which muscle can produce a greater amount of force? Muscle B Muscle A Muscle A and B produce the same force