A wheel of 10 in. radius carries a load of 1000 lb. a. Determine the horizontal force P applied at the center which is necessary to start the wheel over the 5 in. block. Also find the reaction at the block.b. If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and the reaction at the block. Prob324, page 65A wheel of 10 in. radius carries a load of 1000 lb.a. Determine the horizontal force P applied at the center which isnecessary to start the wheel over the 5 in. block. Also find thereaction at the block.b. If the force P may be inclined at any angle with the horizontal,determine the minimum value of P to start the wheel over theblock; the angle that P makes with the horizontal; and thereaction at the block.-101000 IbENRprob. (1). fig. (324)

Answered: Image /qna-images/answer/5b722455-3de2-49e8-b5ab-d1ca290eb28e.jpg

A wheel of 10 in. radius carries a load of 1000 lb. a. Determine the horizontal force P applied at the center which is necessary to start the wheel over the 5 in. block. Also find the reaction at the block. b. If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and the reaction at the block.

A wheel of 10 in. radius carries a load of 1000 lb. a. Determine the horizontal force P applied at the center which is necessary to start the wheel over the 5 in. block. Also find the reaction at the block. b. If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and the reaction at the block.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.41P: The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking...

See similar textbooks

Similar questions

The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The round stepped shaft (diameters d and D) shown below is a design for an exoplanet rover wheel axle. Assuming the wheel is stuck, a torque from the motor is transmitted to the axle but it is not rotating. The reaction of the weight of the rover on the ground and the torque the wheel applies to the ground are represented by the force F acting in the center of the wheel hub (not shown) at point C. There is a sharp fillet at B with radius r shown below. Bearings are shown at point A and next to point B. You may assume the bearing at B resists the bending moment caused by the force F and acts like a fixed reaction. В A L2 L1 T L3 - ØD Ød R. r F SUBMIT ANSWERS HERE: Paramete Parameter Value Value SUT (tension) 400 MPa | L1 400 mm Suc (Compression) 600 Мра L2 200 mm Sy 380 MPа L3 100 mm 600 N-m ø d 40 mm F 0.2 kN ø D 55 mm R. r 8 mm
Q-4. Determine the "Horizontal Displacement" of Joint "A of the below given frame by using the "Method of Virtual Forces". 6 ft B 200 lb -6 ft- 8 ft
Current Attempt in Progress In the special position shown for the log hoist, booms AF and EG are at right angles to one another and AF is perpendicular to AB. If the hoist is handling a log weighing 4380 lb, compute the magnitudes of the forces supported by the pins at A and D in this one position due to the weight of the log. 50° A = Answers: i D= i 15" A 13' 26" B eTextbook and Media E C lb lb R 10" 3' -"( 14' G
Please write solution to be legible and clear. Thanks
Also determine the magnitude of the force at O. Express your answer in units of N.
B3 please text writing ans
Pulley A delivers a steady torque of 1100 lb-in. To a pump through its shaft at C. The tension in the lower side of the belt is 165 lb. The driving motor weighs 200 lb and rotates clockwise. Determine the bearing reaction force at O. A 9" B 30° 37 8" 150 lb - 5"-- 5"-
Also determine the magnitude of the force at O. Express your answer in units of N. Please make sure the answer is numerical value (Do not answer with W).
3. Find the Foroe required to lift the 15 slug cylinder. Draw 3 Free Body Diagrams. 15 slug F
The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge here. Determine the reaction force of the ground and the reaction at the knee joint and its direction/angle θ. Note: use the thee force member condition to find the angle of FK.Q4.As it’s been shown in the below figure,a person is using an exercise machine. Points A and B correspond to the shoulder and elbow joints, respectively. Relative to the person, the upper arm (AB) is extended toward the left (x-direction) and the lower arm (BC) is extended forward (z-direction). At this instant, the person is holding a handle that is connected by a cable to a suspending weight. The weight applies an upward (in the y-direction) force with magnitude F on the arm at point C. The lengths of the upper arm and lower arm are AB̅̅̅̅= 20cm and BC̅̅̅̅= 25cm, respectively, and the magnitude of the applied force is F = 400 N.Determine the components of reaction developed at the shoulder joint A When the…