A well-insulated rigid tank contains 3.5 kg of a saturated liquid–vapor mixture of water at 200 kPa. Initially, three-quarters of the mass is in the liquid phase. An electric resistance heater placed in the tank is now turned on and kept on until all the liquid in the tank is vaporized. Determine the entropy change of the steam during this process. Use steam tables.### Diagram Description:The diagram shows a tank with a liquid-vapor mixture labeled "H₂O" under 200 kPa pressure. Inside the tank, there is an electric resistance heater. The diagram illustrates the phase transition from liquid to vapor due to the heating process.**The entropy change of the steam during this process is ____ kJ/K.**

Given at condition 1 mass of saturated liquid vapor mixture = 3.5 kg Mass of the liquid mf=…

A well-insulated rigid tank contains 3.5 kg of a saturated liquid-vapor mixture of water at 200 kPa. Initially, three-quarters of the mass is in the liquid phase. An electric resistance heater placed in the tank is now turned on and kept on until all the liquid in the tank is vaporized. Determine the entropy change of the steam during this process. Use steam tables. H₂O 200 kPa W

A well-insulated rigid tank contains 3.5 kg of a saturated liquid-vapor mixture of water at 200 kPa. Initially, three-quarters of the mass is in the liquid phase. An electric resistance heater placed in the tank is now turned on and kept on until all the liquid in the tank is vaporized. Determine the entropy change of the steam during this process. Use steam tables. H₂O 200 kPa W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please provide a detailed solution, Don't just put the equation. It's important to provide an explanation.
A 100L tank initially contains water at 100kPa and a quality of 1%. Heat is transferred to the water, raising the temperature and pressure. At a pressure of 3 MPa, a safety valve opens and saturated vapor at 3 MPa flows out. The process continues, maintaining 3 MPa inside until the quality in the tank is 90% and then stops. Determine the total mass of water that flowed out and the total heat transfer.
During a normal inhalation, if the lung volume and pressure are 2500 cm3, 3000 cm3 at 5kPa values, and 10 kPa values, how many Joules is the work done against the elastic forces in this process?
Saturated water at 36.6°C passes through a throttling valve and becomes a mixture of water and steam at 5.4°C. Calculate the specific volume and specific enthalpy of the mixture. Show detailed steps of how the properties are obtained by using only the Saturated Water and Steam table. Consider that a throttling process is a typical irreversible process. The specific enthalpies of the working fluid before and after a throttling valve are the same. The steam table has been provided in the image
Steam enters a diffuser steadily at 300 kPa and 300 oC having a velocity of 80 m/s. The inlet diameter of the diffuser is 0.1 m and the velocity at the diffuser exit is very small compared with the inlet velocity. The heat loss from the diffuser to the surroundings is at a rate of 88 kW. If the exit pressure is 800 kPa, determine the phase description and temperature at the diffuser exit. Neglect the potential energy change throughout the diffuser.
Refrigerant 134a enters a compressor at 600 kPa as a saturated vapor. It exits at 60°C and 1.4 MPa. Determine the entropy change and the isentropic efficiency. Show the process on a T-s diagram with respects to the saturation lines.
An insulated rigid tank is div led into two equal parts by a partition. Initially, one part contains 5 kmol of an ideal gas at 25 kPa and 40°C, and the other side is evacuated. The partition is now removed, and the gas fills he entire tank. Determine the total entropy change during the process.
A mass flowrate of 1 Ibm/s of water at 80 F and 70 pisa is mixed with 1 Ibm/s of saturated vapor water at 70 psia in a mixing chamber. During this process 100 Btu/s of heat is lost from the mixing chamber to the surrounding environment. The exiting stream leaves the mixing chamber at 70 psia. In the question that follows, select the answer that is closest to the true value. What is the quality of the exiting stream ?
Propane initially at 300 K and 100 kPa is is compressed to 1 MPa in a reversible, steady-flow, and compressor. Determine the amount of work in kJ/kg if the process is isothermal. Round your answer to one decimal place
The numbe is 8
Refrigerant 134a enters a compressor at 600 kPa as a saturated vapor. It exits at 60°C and 1.4 MPa. Determine the entropy change and the isentropic efficiency. Show the process on a T-s diagram with respects to the saturation lines. (30)
An insulated piston-cylinder device contains 0.5L of saturated liquid water at a constant pressure of 100 kPa. An electric resistance heater inside the cylinder is now turned on, and 1178.36 kJ of electrical work is transferred to the steam. Determine (a) the entropy change of the water during this process; (b) the entropy generation during this process? 1178.36 kJ M H₂O 100 kPa Sat. liquid