An insulated tank is divided into two parts by a partition. One part of the tank contains 3.5 kg of compressed liquid water at 60°C and 600 kPa while the other part is evacuated. The partition is now removed, and the water expands to fill the entire tank. Determine the final temperature of the water and the volume of the tank for a final pressure of 10 kPa. Use data from the steam tables. Evacuated Partition H₂O The final temperature of the water is 45.8 °C. The volume of the tank for a final pressure of 10 kPa is 1.74 m³

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: i cant read this.. can you write it out??

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 400N 200 Z00 N さ

A: Given Data :

Q: Write the four different types of Resultant Loadings?

A: Loading: The loading on the beam or any members is the load acting on a beam under which beam…

Q: 3

A:

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: In the engine system shown, the lengths of the connecting rode (that is the length of BD) and the…

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: (b) 1489.5m³ (C) 128

A: given:bore diameter d=68mmstroke length l=75mm

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: how did the equation simplify to a = 0.984?

A:

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: name these lines

A: The names of the given lines is given below.

Q: Move the forces in the shape to point a

A:

Q: The bar AB shown in Figure 12-13 moves so that its lowest point A travels horizontally to the right…

A: Given information Velocity of point A, Find  Velocity of point B ,

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Q: handle should be identified as a point of interest. Determine the Degree of freedom.

A:

Q: D= 1.75 in d= 0.75 in r= .120 in

A: Calculate D/d and r/d ratio, Fr calculating the stress concentration factor we use the…

Q: 2y dx

A: Solution given below.

Q: 2x105 Nlmen2 Biomaha uemprog aoo un qans G ) Tatal anctansion the ban

A: Normal stress is defined as the intensity of force exerted on an area perpendicularly. Normal stress…

Q: 66. Which line type is used to indicate the outer form or the edges of the object? Select one:…

A: Solution:

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.