I need the answer quickly Task 3A wave guide fed-pyramidal horn antenna is working at an operating frequency of 10 GHz forthe following lengths: Pg = 6.6cm; PH = 7.78cm. Assuming the Waveguide parameters aswidth: W, = 23.53mm; Height : H, = 11.77mm. For this antenna answer the following:i.Calculate the aperture height (Ha) and aperture width (Wa) ;ii.Calculate the gain (G) of the antenna;iii.Calculate the Flare length (L;) in E plane;iv.Increase the aperture height by 25% and analyze the effect on the gain obtained for thegiven operating frequency;

Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

A wave guide fed-pyramidal horn antenna is working at an operating frequency of 10 GHz for the following lengths: PE = 6.6cm; PH = width: W, = 23.53mm; Height: H, = 11.77mm. For this antenna answer the following: i. 7.78cm. Assuming the Waveguide parameters as %3D Calculate the aperture height (Ha) and aperture width (Wa); ii. Calculate the gain (G) of the antenna; Calculate the Flare length (L,) in E plane; iii.

A wave guide fed-pyramidal horn antenna is working at an operating frequency of 10 GHz for the following lengths: PE = 6.6cm; PH = width: W, = 23.53mm; Height: H, = 11.77mm. For this antenna answer the following: i. 7.78cm. Assuming the Waveguide parameters as %3D Calculate the aperture height (Ha) and aperture width (Wa); ii. Calculate the gain (G) of the antenna; Calculate the Flare length (L,) in E plane; iii.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Complete solution otherwise skip. Plxxx.
A 150 MVA, Synchronous generator has a moment of inertia 47000 Kg-m2 and Kinetic Energy 1600 MJ. The synchronous speed of generator is
I need the answer as soon as possible
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
The contractor is controlled by?
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
Hey see
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies