A water tower is used to supply a fire protection system as shown in Figure 10.5. The water tower and the standpipe are 24.4 m tall. The long horizontal pipe is 182.9 m. It is made of cast iron. There is one gate valve at the end of the long pipe. Neglect any other minor losses. What is the maximum flowrate through the pipe? Determine the maximum flowrate when the pipe is new (8-0.26 mm) and when it is 20 years old (double the roughness due to corrosion).

A water tower is used to supply a fire protection system as shown in Figure 10.5. The water tower and the standpipe are 24.4 m tall. The long horizontal pipe is 182.9 m. It is made of cast iron. There is one gate valve at the end of the long pipe. Neglect any other minor losses. What is the maximum flowrate through the pipe? Determine the maximum flowrate when the pipe is new (8-0.26 mm) and when it is 20 years old (double the roughness due to corrosion).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the power requirement of the pump shown in Figure 3.0, assuming it has an efficiency of 88%. The system has a loss coefficient of 3.0 up to point A, and K =1.2 from point B to point C. Neglect any losses through the exit nozzle. Additionally, compute the pressures at points A and B. Water 15 m 2 cm 4 cm dia. 5 cm dia. Figure 3.0 400 kPa
State clearly your assumptions in your solution sheet
What is the formula of modulus of elasticity. Write it's unit.
Describe and Draw Energy Grade Line (EGL) &Hydraulic Grade Line (HGL) Describe and write the formulas measuring flow rate in pipes using Orifice.
Question 8 download image D The water in a large tank exits through a horizontal circular pipe of diameter D=0.01m and length L=94m. The centre of the exit of the pipe is h=1.0m below the water surface. We can assume that the flow entrance to the pipe is smooth so that there are no minor losses. The flow in the pipe is laminar, the friction factor can be assumed constant and can be found from h fD=64/Rep where the Reynolds number is based on the pipe diameter and mean flow speed in the pipe. Taking frictional losses into account, solve the resulting quadratic equation to calculate the speed of the flow out of the pipe. Give your answer in m/s to 2 decimal places. Use: kinematic viscosity given by v=0.00000114 m²/s density of water given by 1000 kg/m3 acceleration due to gravity of 9.81 m/s² A Moving to another question will save this response. >>
The overall loss coefficient for the pipe shown in Fig.3 is 5; up to A it is 0.8, from A to B it is 1.2, from B to C it is 0.8, from C to D it is 2.2. Estimate the flow rate and the pressures at point C The elevations are shown. el. 12 m el. 10 m Water el. 3 m A B C 8 cm dia. D 3 cm dia. el. 0
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200- 150 - 6 125- Suction lines 100 - 4 3. 65 2 50E 2 Discharge lines 40 - 32 - 25 E 15 15 20 30 40 60 200 400 600 S00 2000 4000 6000 S00 80 100 10 Volume Flow Rate, Qallmin) 8 10 15 20 25 30 40 +++++ +++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 +++++ +++++ Volame Flow Rate, Q (mVh)
4. Water (p = 1000 kg/m³) is transferred from a large lake to an open storage tank located at elevation as shown in the Figure 2 below at a flowrate of 90m³/hr. The losses through pipe and fittings (hL) is given as 8m. Determine the mechanical efficiency of the pump if the shaft power required is 12kW. State the assumptions made in your calculations. 30 m WaterLevel Pump Centre Figure 2 Tank
10. Water at 25 °C is transferred 10 m high to the first floor using stainless steel pipes (e = 2 x 10-6 m) with a diameter of 2 cm. If the water leaves through a faucet of diameter 1.3 cm at a flow rate of 8 x 104 m³/s. Determine the required pressure at point 1 (P1) if: a) All viscous effects are ignored b) Only major losses are considered c) All loses are considered (major + minor) Assume that the density and viscosity of water at 25 °C is 997 kg/m and 0.891 x 10-3 kg/m.s, respectively. You can use relevant tables and Moody chart to find the required properties. L=4m L-4 m L= 4 m K, = 2.5 10 m K- 1.5 K, = 0.5 L= 4 m K, 8 Water L=5m L%3D4M
find the diameter through circular duct if the flow rate (0.98 m3/s) and velocity(5m/s) Fulleen Snip 280 mm 490 mm 560 mm 750 mm 820 mm
Calculate the Flow Rate of water at 5°C through the system below. Q = Flow 3.4 m 700 kPa 30 mm diameter DN 65 mm Schedule 40 Pipe