A water sample was tested for hardness. To titrate Ca2* and Mg2+, a 25.00-mL sample needed 7.39 ml of 0.00964 M EDTA. Another 25.00-mL aliquot was mixed with sufficient NaOH to precipitate out Mg2* as Mg(OH)216). Titration of the clear supernatant liquid required 4.54 mL of the same standard EDTA solution. FW: CaCO3 = 100.09, Mg = 84.31, Ca = 40.078 %3D (Report answers in 3 SF.) a. Calculate the concentration of CaCO3 (FW=100.09) in the sample in ppm. ppm a. Calculate the concentration of MgCO3 (FW=84.31) in the sample in ppm. ppm

A water sample was tested for hardness. To titrate Ca2* and Mg2+, a 25.00-mL sample needed 7.39 ml of 0.00964 M EDTA. Another 25.00-mL aliquot was mixed with sufficient NaOH to precipitate out Mg2* as Mg(OH)216). Titration of the clear supernatant liquid required 4.54 mL of the same standard EDTA solution. FW: CaCO3 = 100.09, Mg = 84.31, Ca = 40.078 %3D (Report answers in 3 SF.) a. Calculate the concentration of CaCO3 (FW=100.09) in the sample in ppm. ppm a. Calculate the concentration of MgCO3 (FW=84.31) in the sample in ppm. ppm

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A 1.000 mL aliquot of a solution containing Cu²+ and Ni²+ is treated with 25.00 mL of a 0.03703 M EDTA solution. The solution is then back titrated with 0.02138 M Zn²+ solution at a pH of 5. A volume of 22.13 mL of the Zn²+ solution was needed to reach the xylenol orange end point. A 2.000 mL aliquot of the Cu²+ and Ni²+ solution is fed through an ion-exchange column that retains Ni²+. The Cu²+ that passed through the column is treated with 25.00 mL of 0.03703 M EDTA. This solution required 18.53 mL of 0.02138 M Zn²+ for back titration. The Ni²+ extracted from the column was treated witn 25.00 mL of 0.03703 M EDTA. How many milliliters of 0.02138 M Zn²+ is required for the back titration of the Ni²+ solution? volume: mL
What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA solution? Assume that 1.758 M EDTA solution was computed based on the titration of CaCO3 standard. The volume of titrant needed to reach the endpoint was 35.00 mL. Ca2+ + Y4- → CaY2- 0.1500 g 5.630 g 6.158 g 0.6158 g
The calcium content of a milk sample was to be determined by EDTA titration. A sample weighing 0.206 g was mixed with an aqueous buffer at pH 11.5. A few drops of EBT indicator were added and the solution required 24.25 mL of 1.538 x 10-2 M EDTA to reach the endpoint. Calculate the weight percent of calcium (FW =40) in the milk.
In the titration of MgSO4.2H2O (2g per litre) against a 0.01 M solution of the disodium salt of ethylenediamine tetraacetic acid (EDTA) the titres obtained were as follows ; titre 1: start - 0.7 ml and end - 13.3 ml (12.6ml) titre 2: start - 13.3 ml and end 25.7 ml (12.4ml) The average titre is 12.5ml Q. Calculate, based on the average titre of the accurate titres, the percentage of magnesium in the magnesium salt
1. A 0.7120 g of iron ore was brought into solution and passed through a Jones reductor. Titration of Fe(II) produced required 39.21mL of 0.02086M KMnO4. Express the results of analysis in terms of (a) percent Fe (MM 55.85) and (b) percent Fe₂O3 (MM 159.69). 5Fe +2 + MnO4 +8H+ → 5Fe+³+ Mn+² + 4H₂O
Calculate PCa of the solution that results when 50.0 mL of 0.0050 M Ca2+ is titrated with 25.00 mL of 0.0100 M EDTA in a solution buffered to a conastant pH of 10.00.
An unknown solution containing 25.00 mL of Ni2+ in dilute HCl is treated with a known excess of 25.00 mL of 0.05382 M EDTA solution. The solution turns yellow when a few drops of indicator are added. The excess unreacted EDTA back titrated with 0.02299 M Zn2+, which requires 17.00 mL to reach the red end point. What is the molarity of Ni2+ in the unknown solution?
A 25.00 ml of Ni2* solution was diluted in HCI and treated with 25.00 ml of 0.05283 M NazEDTA. The solution was neutralized with NaOH followed by addition of acetate buffer until the pH 5.5. The solution turns yellow after addition of few drops of xylenol orange indicator. Back titration using standard 0.022 MZn2* at pH 5.5 requires 17.61 ml until end point, on which the solution will turn red. Calculate for the molarity of the unknown. Ans. 0.03664 M
The amount of calcium in physiologic fluids can be determined by a complexometric titration with EDTA. In one such analysis, a 0.100-mL sample of blood serum was made basic by adding 2 drops of NaOH and titrated with 0.00528 M EDTA, requiring 0.233 mL to reach the end point. Report the concentration of calcium in the sample as miligrams of Ca per 100 mL. (Ca = 40.078 amu).