A water jet consumes 450 W for 24 hours a day. 1. What is the energy consumed (kWh) for one year period? 1 year = 362.25 days. 2. What is the utility energy charges for this period at a rate of 600 pesos /kWh? 3. What is the energy cost savings for this period if the water jet is switched of 8 hours a day? %3D

A water jet consumes 450 W for 24 hours a day. 1. What is the energy consumed (kWh) for one year period? 1 year = 362.25 days. 2. What is the utility energy charges for this period at a rate of 600 pesos /kWh? 3. What is the energy cost savings for this period if the water jet is switched of 8 hours a day? %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

explain breifly the homework question
Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
this is incorrect!!!!!! answer should be vab=20v and req=6 ohms please resolve in detail and with a good explanation as to how you reached the answer AND ONLY SUBMIT IF IT IS IDENTICAL TO THE ANSWER I HAVE GIVEN. if correct thumbs up is ready and thank you
Choose the correct answer In the USA, the heating element inside a hairdryer is marked as follows: (120V, 2400W). What is the resistance of the filament in the lamp? (HINT: Use Ohm's Law and power "law" equations). A. 10 ohm B. 4800 ohm C. 2 ohm D. 6 ohm
Answer Question 1 Subject: Renewable Energy Systems Last Digit: 15 For Solar: 1200W, 5A, 5 strings, 4 cells in each string, the cell is (60 V, 1A) And, for Wind: 800W Need calculation, figure and proper explanation. A smart home is connected to micro grid as well as utility grid. The micro grid consists of solar and wind energy. Solar power plant meet 60% of energy demand of smart home while rest is from wind power plant in normal oper- ating condition of both power plant. The smart home rated consumption power is 2000 W (Centrifugal pump, static load each 50%). 1. Design your micro grid power generation system which can meet the power consumption requirement of the smart home. Note: Solar array should contain at least two strings depending your two digit of your ID number. Please submit your IDs for getting the number of strings.
Question 3 (a) Discuss and critique the law of electricity supply? (b). Explain with a diagram a Retail competition model of electricity market. (c). Explain effects when government has a bigger say in the operation of Public utilities.
2. A single grounding rod electrode is installed in soil. The electrode's resistance to a good known ground is28 ohms. The next ground rod should be installed at least _______ feet away from the first groundingelectrode.A. 15B. 6C. 10D. 25
What is the meaning of the acronym, XLPE? O A. CROSS-LINED POLYETHYL EQUIPMENT O B. CROSS-LINKED POLYETHYLENE O C. EXTRA LOW POLYESTER EQUIPMENT O D. EXTREMELY LINED POLYMER EXTRUSION
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
What causes the normal heating in electronic devices? Not things that cause an anormal disfunction like dust or something else, but the one thing that by default creates normal heat in a system. I mean the actual part of the device which creates that heat.
A PMMC instrument has internal resistance of 0.8 kΩ and gives full scale deflection for 33 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 75 V will be __________________ ohms. a. 226.47 b. -360.00 c. 1472.73 d. 93717.00
please answer the questions in terms of electric car