A water-cooled spherical object of diameter 10 mm and emissivity 0.9 is maintained at 4000 C. What is the net transfer rate from the oven walls to the object? A surface of area 0.5 m² , emissivity 0.8 and temperature 150 °C is placed in a large, evacuated chamber whose walls are maintained at 25°C. What is the rate at which radiation is emitted by the surface? What is the net rate at which radiation is exchanged between the surface and the chamber walls?

A water-cooled spherical object of diameter 10 mm and emissivity 0.9 is maintained at 4000 C. What is the net transfer rate from the oven walls to the object? A surface of area 0.5 m² , emissivity 0.8 and temperature 150 °C is placed in a large, evacuated chamber whose walls are maintained at 25°C. What is the rate at which radiation is emitted by the surface? What is the net rate at which radiation is exchanged between the surface and the chamber walls?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM: IVD-19 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
It is desired to heat the workshop with a stove made of falling cylindrical sheet material with an outer diameter of 400 mm and a height of 1600 mm. The surface temperature of the stove is 217 oC and the radiation emission coefficient is 0.92, the temperature of the workshop surfaces is 12 oC and the ambient temperature of the workshop is 17 oC. Next to the stove, the workshop surface area is very large. From the side surface of the stove to the workshop; a) By transport,b) with radiation Calculate the heat transfer.
answer asap for upvoteskip if you already did this or else downvote
A quartz radiant heater has two cylindrical tubes 40 cm long and 1 cm radius. The heater is designed to produce 1300 watts of radiant power. What would be the temperature of the tubes if the emissivity of the tubes is 0.60. a. 570 K b. 934 K c. 980 K d. 1068 K
Molten metal at 2000 C is poured using crucible. The liquid metal jet has a diameter of 3 mm with an insulation shield of 5 cm diameter. There is a slit of 30 degrees around the insulation shield. The temperature inside the room is 30 C and the shield is 700 C. Assuming black bodies, find the net heat transfer between jet and shield, jet and room, shield and the room. One of the steps is wrong A) Resistance network is required to be built B) To find the view factor between metal and shield , ratio of the angles is used C) View factors are one of the most important steps to solve the problem D) None of the above E) Slit doesnot participate in radiation
Pravinbhai
A long, thin-walled horizontal tube 10.0cm in diameter with an emissivity of 0.80 is maintained at 120.0°C by the passage of pressurized steam inside the tube. To reduce radiation heat transfer losses, a round, tubular radiation shield with an emissivity of 0.10 is installed surrounding the heated tube, with a gap of 1.00cm between the outside of the tube and the radiation shield. At steady-state operating conditions, the temperature of the radiation shield is measured to be 35.0°C. Calculate the total heat transfer rate per meter length assuming that the gap between the pipe and heat shield is now filled with air at a pressure of 1.00 atm.
This experiment is conducted to determine the emissivity of a certain material. A long cylindrical rod of diameter D₁ = 0.01 m is coated with this new material and is placed in an evacuated long cylindrical enclosure of diameter D₂ = 0.1 m and emissivity 2 = 0.95, which is cooled externally and maintained at a temperature of 200 K at all times. The rod is heated by passing the electric current through it. When steady operating conditions are reached, it is observed that the rod is dissipating electric power at a rate of 16 W per unit of its length, and its surface temperature is 600 K. Based on these measurements, determine the emissivity of the coating on the rod. The emissivity of the coating on the rod is 0.1165
10-cm-diameter hemisphere in Figure Example 8-8 is maintained at a constant temperature soo°C and insulated on its back side. The surface emissivity is 0.4. The opening exchanges adiant energy with a large enclosure at 30°C. Calculate the net radiant exchange
A tube pipe is heated to a temperature of 150°C with an outside diameter of 12cm and it’s enclosed in a large room of 20°C. Calculate the radiant heat loss per unit length, if the surface emissivity is 0.65.
2. A heater is a thin vertical panel 1.0m long and 0.7m high and is used in a warehouse to keep workers warm. The heater has air circulating on each side. Assume the maximum temperature of the panel is 60°C (already above the board line that is safe for human hands to touch briefly without getting hurt). Assume the room air temperature is 18°C but the warehouse wall temperature is 5°C. Model the surface with an emittance of 0.9 and Vair = 1.57x105 m²/s. a. Determine the maximum power rating for the heater. b. Now if you run the heat by standing on its side (it will be 1.0 m high and 0.7 m long), determine the surface temperature. c. Compare case a and b and explain any differences you see.
Two parallel discs pf 1m diameter are situated 2m part in surroundings at a temparature 20 C. The inner side of one disc has an emissivity of 0.5 and is manintained at 500 C by electric resistance heating and the outer side of the disc is well insulated. The other disc is Two parallel discs of 1m diameter are situated 2m apart in surroundings at a temperature of 20 oC. The inner side of one disc has an emissivity of 0.5 and is maintained at 500 oC by electric resistance heating and the outer side of the disc is well insulated. The other disc is open to radiation on both sides and reaches an equilibrium temperature. Calculate this equilibrium temperature and the heat flow rate from the first disc, assuming heat transfer is entirely by radiation.