A W250X101 is used as a  6.1 m - long column. It is fixed at the bottom and fixed against rotation but free to translate at the top. Use ASD and Fy = 345 MPa. If the column will carry a service axial dead load of 387 kN, calculate the service axial live load (kN) it can carry.

Q: 4m + 6m EA 1 77777 D 4 rigid 5m 3 kN/m Figure-3 7m 4444 2EA B₁ 1 1 1 I The rigid beam AB in Figure 3…

A: To find the stress in bar 1 and 2

Q: MA -L/4- -L/2- -L/2- -L/4-

A: part a will be solved given- a beam with one end overhange carrying udl and uvl loading. required-…

Q: The cantilever beam (of type W8 × 15) made of A36 steel alloy has a depth d =8.11 in, as shown…

A: As per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts. Kindly repost…

Q: Consider a fixed beam AB of span 1 subjected to a uniformly distributed load 'w' kN/m on half of its…

A: For a given arrangement,For a fixed beam AB of span l subjected to uniformly distributed load 'w'…

Q: 2. [Ac, 0c] Use conjugate beam method. (EI is constant) 30 ft B 15 ft 15 k C

A:

Q: The cantilever beam shown in figure (2) supports the roof of a workshop shed "no-ceiling". Design…

A: l = 18feet = 216inch w = 1.3 + 2.7 = 4kip/ft M = wl2/2 =  4 x 182/2 = 648 kip-ft Let the material be…

Q: P A B C D -L/3- L/2- L/2- PROBLEM 9.58 For the beam and loading shown, determine (a) the reaction at…

A: EI = constantDeterminea. The support reaction at A. b. The deflection at midpoint C.

Q: The beam supports the loads as shown in the figure. Using E=200 GPa, w = 24 kN/m, P = 8 kN and M =…

A:

Q: A built-up section is made from 450mm x 20mm as flanges and 500mm x 20mm as web as shown. All plates…

A: Answer  (A) Calculation of Moment of inertia along the Neutral axis  Since the section is…

Q: For the beam shown below, determine the concrete and steel stresses at the locations of the maximum…

A:

Q: ). Find the bending moment at 4 (M4) ■). Find rotational displacement at 2(0₂) El=10 000tm² NOTE:…

A: Given a frame loaded at joint 2.Required : the member end moment at 4 in member 2-4 and the…

Q: Both sections are made of steel with E-200 GPa. The gap between the bottom of the metal bar and the…

A: Given data: Length of section AB, L1=300 mm Length of section BC, L2=300 mm Area of section AB,…

Q: 2. The shaft shown has the following properties: Outer diameter, in Inner diameter, in inches SET…

A:

Q: ad moments, and bend ad. K=K,= 1.0. Use LRF

A: (a) Calculate the factored axial compressive load. Here,  is the dead load,  is the live load.…

Q: 10–59. The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is…

A:

Q: Replace the loading system by an equivalent resultant force and couple moment acting at point O.

A: The given figure is shown below:

Q: A K D 2m 4 kN C E 0.5 m ↓ 0.5m 2m B

A:

Q: The loads on a beam section are shown in the figure below. Determine whether the beam is adequate to…

A:

Q: Built-up column 10 m long consists of W350x90 with two 12 mm thick plates welded to form a box…

A:

Q: Based on the bridge truss show below determine the force acting at members DF, GI, and LM using…

A:

Q: A beam is shown in the figure given below where A is hinged, and B and C are roller supports. Use…

A: Consider the free body diagram ; Expression of three moment equation as;…

Q: The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.753…

A:

Q: A W14x61, A992 steel, 6.5 m long fixed at both ends, is to be investigated for use as a column in a…

A:

Q: 2Lx3 x4-L³x); (b) 5W0L* 384 El ximum displacement of the cantilever beam cau Pa² (3L-a) ance from…

A:

Q: Compute the reactions and member forces for the two-span continuous truss shown in the figure.…

A: Trusses are structures consisting of triangle-shaped members arranged in such a way that they form…