A viscous liquid (p = 1.2x10³kg/m³, μ = 0.0048 Pa.s) flows at a rate of10ml/s through a horizontal, 4 mm diameter tube. The pressure drop alonga 1 m length of the tube which is far from the tube entrance so that theflow is fully developed is (kPa)

Answered: Image /qna-images/answer/806b1e0e-fe4b-4373-8d44-5dca2c569291.jpg

Answered: A viscous liquid (p = 1.2x10³kg/m³, u =…

A viscous liquid (p = 1.2x10³kg/m³, u = 10m//s through a horizontal, 4 mm diamete a 1 m length of the tube which is far from

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Liquids A, B and C, in the containers shown, have SG of 0.60, 1.00 and 1.60 respectively. At what elevation (EL. C) will the liquid C stand in each of the piezometer tubes? Round your answer to the nearest hundredths. Pair = 12.5 kPa EL. 8 A (SG =) EL. 6 B (SG =_) %3D EL. 2 C (SG = EL. 0
4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the summit is 6 cm and from the summit to the exit is 23 cm of oil. a. Calculate the exit velocity. b. Calculate the pressure at the summit. 0.6 8.3 76- mm 0 siphon
An orifice in the side of a tank discharges water under a head of 10ft. If the diameter of the orifice is 2m, the coefficient of contraction is 0.63 and the head lost is 0.80ft, determine the discharge. (A) 0.3438 cfs (B) 0.4383 cfs 0.3348 cfs 0.4338 cfs
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
A cylindrical tank with its axis horizontal has a length of 6 m and the ends of the tank are vertical planes, as shown in Figure Q2 (a). The vertical pipe of 0.2 m in diameter is connected to the top of the tank. The tank and the pipe are filled with ethyl alcohol to a level of 1.5 m above the top of the tank. The diamter is 2.07m.
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
two vertical tanks, one with circular section 3.0m in diameter, the other square section 1.33 x 1.33m are connected by a short tube ( area is 0.725 sq. cm) near bottom.initially, the head of oil in the first tank is 4.0m, while in the second tank the head is 60m. After a quick opening of the tube valves, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with c= 0.78
Given: As = 3m2 C = 0.92 Ao = 0.01m2 Find: Determine the time for the depth of liquid in the tank to be 0.8m
Q3. SAE 30 oil (Sp. Gr. =0.833) with a dynamic viscosity 0.28 N.S/m? flows in a 4-cm-diameter pipe which is inclined with an angle 37°. For the pressure measurement shown, determine A. Whether the flow is up or down The flow rate in m'/h C. The shear stress and velocity 1 cm from the boundary Draw the shear stress and velocity profile with the section of the pipe. В. D. P-180 kPa P- sOokPa 15m 20m
A suspended gate that’s able to pivot from the top seperates two liquids. There is a stopper that prevents the gate opening anti-clockwise. The gate has a height of 0.5m. The liquid on the right is three times as dense as the liquid on the left. The liquid on the left has a depth of 0.3m. 1) What is the minimum depth of liquid on the right for the gate to open. 2) Comment on the ability to solve this question if the liquid on the left was 0.5m (filled to the top)