A viscous and incompressible fluid with a density of p is flowing steadily between two parallel platesseparated by a distance of 2h. At section 1, the velocity, U., is uniform, while the velocity distributionat section 2 is assumed to be linear. The flow is identical in all planes, which are parallel to the xy-plane. The pressures at sections 1 and 2 are p₁ and p₂, respectively. Determinea) the maximum velocity at section 2 andb) the drag force exerted on the plates.SolutionYU2hn₁Control volume12

Since the flow is steady and incompressible, the mass flow rate must be conserved between sections 1…

Answered: A viscous and incompressible fluid with…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An incompressible viscous flow is contained between two parallel plates separated from each other by distance b. as shown in Figure 1. The flow is caused by the movement of the upper plate which has a velocity U, while the bottom plate is fixed. If U =3 m/s and b= 2.2 cm, and there is no pressure gradient in the flow direction. Fig Q1: Flow between two plates. The bottom is fixed and the upper is moving. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3. a) What is the velocity at the point x = 5 cm and y= 0.53 cm. Use Navier-Stokes equations. b) What is the magnitude value of vorticity at the same point. c) What is the rate of angular deformation at the same point.
A2 A Newtonian fluid with viscosity (Mu) flows upward at a steady rate between two parallel plates that make an angle y with the horizontal. The fluid thickness h is much smaller than the width of the channel W. The pressures at each end, P(0) and P(L), are known and the pressure variations in the y-direction are small. Assume that Vy and Vz = 0 and Vx is a function of y alone. Use the shell balance to approach : - the Total flowrate, QV
Consider incompressible Newtonian fluid flow between parallel plates (Fig. 4) that are horizontal and a distance h apart. The plates can be considered as very wide and very long so that the flow is essentially axial; hence, u ≠ 0 but v = w = 0 and ∂/∂z=0. B represents the plate width. The flow is fully developed laminar and steady.
Please help me in answering the following practice question. Thank you for your help. A Newtonian fluid is flowing in an infinitely long round pipe of diameter M or radius N = M/2 and inclined at angle α with the horizontal line. Consider the flow is steady (dρ/dt=0), in-compressible, and laminar. There is no applied pressure gradient (dP/dz= 0) applied along the pipe length (z-direction). The fluid flows down the pipe due to gravity alone (gravity acts vertically downward). Adopt the coordinate system with z axis along the centre line of the pipe along the pipe length.Derive an expression for the z-component of velocity u as a function of radius N and the other parameters of the problem. The density and viscosity of the fluid are ρ and u, respectively.Please list all necessary assumptions.
7. Two parallel plates separated by 15.5 cm move with a relative velocity of 7 m/s. How much force per unit area is required to maintain the velocity difference if the fluid separating the plates is (a) water with µ = 1 cP (b) SAE 30 motor oil with µ = 200 cP and (c) honey with µ = 10,000 cP?
A Newtonian fluid is flowing in the narrow gap between two infinite parallel horizontal plates due to the movement of the top plate (see the figure below). The top plate is moving at a speed U from left to right, and the bottom plate is stationary. Consider the flow is steady, incompressible, and laminar. The distance between two plate is H, and the gravity acts in negative z-direction (which is perpendicular into the page). There is an applied constant pressure gradient of apJəx in the x-direction. Calculate the velocity and pressure fields. Plot typical velocity profiles in dimensionless form for a pressure gradient value of 0 and -15. In your solution show the conceptual diagram of the problem; write all relevant assumptions and boundary conditions; show the detailed steps of the problem solutions including equations and detailed processing of those equations. Moving plate Fluid: p.H Fixed plate P2-P1
4. Consider a viscous flow inside an annular pipe. The inner surface of the pipe is located at r = R₁ and is stationary. The outer surface is located at r = Ro and moves to the right with speed Upipe. The pressure inside the pipe is constant. The fluid inside the pipe has dynamic viscosity μ. Assume that the flow is steady, incompressible, fully-developed, axisymmetric, non-rotating, and has negligible body forces. Starting from the differential form of the conservation of mass and momentum equations: a. Derive an equation for the velocity inside the pipe in terms of Upipe, R₁, Ro, and r. b. Determine the average velocity inside the pipe in terms of Upipe, R₁, and Ro. C. Determine the shear stress acting on the inner annulus in terms of Upipe, Ri, Ro, and u. Upipe er R₁ fluid
6) Air flow though the device shown in figure. Select which set of the following conditions is TRUE assuming incompressible non-viscous steady flow (a) p4 v3 (c) p2>p3; v2 > v3 (e) p4> pl; v4 pl; v1 > v3 (d) p4 vl "OUT
Consider steady, incompressible, laminar flow of a Newtonian fluid in an infinitely long round pipe of diameter D or radius R = D/2. We ignore the effects of gravity. A constant pressure gradient ∂P/∂x is applied in the x-direction, where x1 and x2 are two arbitrary locations along the x-axis, and P1 and P2 are the pressures at those two locations. Note that we adopt a modified cylindrical coordinate system here with x instead of z for the axial component, namely, (r, ?, x) and (ur, u?, u). Derive an expression for the velocity field inside the pipe and estimate the viscous shear force per unit surface area acting on the pipe wall.
An incompressible viscous flow is contained between two parallel plates separated from each other by distance b. as shown in Figure 1. The flow is caused by the movement of the upper plate which has a velocity U, while the bottom plate is fixed. If U =7 m/s and b= 1 cm, and there is no pressure gradient in the flow direction. A.) Start with Navier-Stokes equations and determine the velocity at the point x = 3 cm and y= 0.41 cm. The value of the velocity is.B.) Calculate the magnitude of the vorticity at the same point. The magnitude value of vorticity. C.) Calculate the rate of angular deformation at the same point. The angular deformation value
The velocity components in the x and y directions are given by 3 u = Axy3 - x2y, v = xy2 -- The value of a for a possible flow field involving an incompressible fluid is
Consider a steady, incompressible, y=+h ↑y hydrodynamically fully-developed flow between two infinite flat plates as shown. The flow can be described by the following equation: y=-h 2U K -y² +C¸y+C, 2µ where u is the dynamic viscosity, u is the axial velocity (i.e., the velocity in x-direction), and K, Cı, and C2 are constants. (a) Obtain the velocity profile u(y) in terms of h, U, K, µ̟ and y. (b) For what value of K is the shear stress zero at y=h/2. Consider h=0.01 mm, U=0.1 mm/s, and u=0.001 Pa.s

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS