A very wide plate with a 2" long center crack is heated in order to be brazed to its end supports. The plate is made of a material with an Elastic modulus of 15x10⁶ psi and α = 6x10⁻⁶ in/in/°F. Considering the brazed ends become rigid supports at 400°F and assuming that the material has a constant Fracture Toughness of 30 ksi√in, at what temperature will the plate fracture? [hint: use β (geometric factor) = 1.0 for this geometry]The diagram below the text shows a rectangular plate with a horizontal crack in the center, represented by a dashed line. The ends of the plate are shown as being connected to supports, indicated by diagonal lines.

Answered: Image /qna-images/answer/95125bbe-6335-4107-b7d8-ef67316dd717.jpg

A very wide plate with a 2" long center crack is heated in order to be brazed to its end supports. The plate is made of a material with Elastic modulus of 15x10ºpsi and a = 6x10- in/in/°F. Considering the brazed ends become rigid supports at 400°F and assuming that the material has a constant Fracture Toughness of 30ksivlin, at what temperature will the plate fracture? [hint: use ß (geometric factor) =1.0 for this geometry]

A very wide plate with a 2" long center crack is heated in order to be brazed to its end supports. The plate is made of a material with Elastic modulus of 15x10ºpsi and a = 6x10- in/in/°F. Considering the brazed ends become rigid supports at 400°F and assuming that the material has a constant Fracture Toughness of 30ksivlin, at what temperature will the plate fracture? [hint: use ß (geometric factor) =1.0 for this geometry]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An Al2O3 part contains both internal cracks with a maximum length of 0.075 mm, and external cracks with a maximum length of 0.05 mm. At what applied stress will the internal cracks begin to propagate? At what applied stress will the external cracks begin to propagate? The fracture toughness KIC = 1.76 MPa x m1/2, Y=1.
You have been asked to draw up a specification for a ceramic cladding tile that is likely to experience tensile stresses of 64 MPa during its installation and service lifetime. If the ceramic has a specific surface energy of 0.28 J/m2 and its Youngs Modulus is 82 GPa what would be the maximum length of an internal flaw that would not result in fracture of the tile? (This question has only one correct answer) O a. 3.79 mm O b. 7.14 mm c. 7.57 um Ο d.3.79 μm O e. 3.57 µm O f. 3.57 mm g. 7.14 um
A cylindrical steel pressure vessel D-575 mm in diameter with a wall thickness of 5 mm is subjected to an internal pressure of 3 MN/m². Calculatea- the tangential and longitudinal stresses in the steel.b- To what value may the internal pressure be increased if the stress in the steel is limited to 80 MN/ m²?c-If the internal pressure were increased until the vessel burst, sketch the type of fracture that would occur
(a) A large medium carbon steel crane hook is thought to contain penny- shaped internal cracks. If the non-destructive test equipment used on the hook is not capable of detecting cracks smaller than 20 mm diameter, determine the fracture toughness required from this steel if the safety factor on stress is to be 2. The yield stress of the AISI 1045 grade steel is 1050 MNm². Note: For this crack geometry, the 'compliance function' Y in the Stress Intensity Factor (K)) may be taken as 1. (b) A surface crack of 2.5 mm depth and a certain length is found in a thick rectangularcomponent. The component is schedule to be repaired in 6 months. The component is subjected to zero to maximum stress of 340 MPa, 50 times per hour. It was known that for this component catastrophic failure occurs when the crack size reaches 12 mm in depth. Assuming that the crack geometrical shape (aspect ratio) remains constant during crack growth, will the component fail before repair? For the crack geometry, the…
Suppose that a wing component on an aircraft is fabri- cated from an aluminum alloy that has a plane-strain fracture toughness of 26.0 MPa Vm (23.7 ksi Vin.). It has been determined that fracture results at a stress of 112 MPa (16,240 psi) when the maximum internal crack length is 8.6 mm (0.34 in.). For this same component and alloy, compute the stress level at which fracture will occur for a critical internal crack length of 6.0 mm (0.24 in.).
1. Glass and epoxy have stiffnesses of Eglass = 70 GPa and Eepoxy = 3.5 GPa and fracture toughness values of Kic-glass = KIC-epoxy = 1 MPa√m. a. Which has a higher toughness (GC)? b. What might the broken surfaces look like after failure, and how does that relate to the energy dissipated during fracture?
Need help on this