A vertical sluice gate 3m wide and 2.5m deep contains water on both of its sides. On the upstream side, the water is 5m deep and on the downstream side it is 2m deep from the bottom of the sluice. What is the resultant pressure on the gate? Water 5m 111 711 111 Hinge 111 2.5m 2.5m Water 2m 7K

A vertical sluice gate 3m wide and 2.5m deep contains water on both of its sides. On the upstream side, the water is 5m deep and on the downstream side it is 2m deep from the bottom of the sluice. What is the resultant pressure on the gate? Water 5m 111 711 111 Hinge 111 2.5m 2.5m Water 2m 7K

Name: A vertical sluice gate 3m wide and2.5m deep contains water on both of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A vertical sluice gate 3m wide and2.5m deep contains water on both ofits sides. On the upstream side, thewater is 5m deep and on thedownstream side it is 2m deep fromthe bottom of the sluice. What is theresultant pressure on the gate?Water5m1112.5mH

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through a horizontal pipe of cross sectional of 20 cm2. Atone section, the cross sectional area is 4 cm2. the pressure difference is29.4 psi. How many cubic meters of water will flow out of the pipe in 1min? (can you show the diagram or illustration if possible. thank you!) Choices: a. 0.008 b. 1.208 c. 0.493 d. 0.0185
Q4//Determine the required vertical force F to be applied at the lower edge to open the square gate (2.8m*2.8m) as shown in figure below: Negative pressures 8250Pa 1.8m Gasoline s-0.7 hinge gate
A spherical buoy is moored to a river bed. The river flows from left to right. Because of flow, the line that ties the buoy is tilted 5° from the upright position, as shown in the graph to the right. At this location the top surface of the buoy is just below the water surface. The effective specific gravity of the buoy is 0.65. The diameter of the buoy is 2 ft and the line is 4 ft in length. What is the force acting on the line? What is the horizontal force acting on the buoy that comes from the flow? Surface Flow 85°
Problem 5: Energy Equation This question tests your ability to recognize the components of the energy equation: Ply+z+V²/(2g) = constant. On your submission, write each of the following six concepts, then write the relevant component (or "none"): elevation head P/Y pressure head P/Y dynamic head P/y P/Y neglect for steady flow neglect for horizontal flow neglect for open channel flow Ply P/Y Z V²/(2g) V²/(2g) v²/(2g) Z V²/(2g) V²/(2g) V²/(2g) Z Z N N none none none none none none
Please fast only final answer needed
Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force required to keep the junction box in place. Assume water at 4°C. 250 mm Q₁ = 0.2 m³/s P₁ = 480 kPa 350 mm 300 mm QIVA = 0.3 m³/s /P = 400 kPa 30° Q=0.1 m³/s Pc = 450 kPa 50⁰ 200 mm 60° Q = 0.4 m³/s PD = 350 kPa
magnitude of the reruttant water force Cper meter op width) acArngs on the face of the dam? A grauity dam has the cross section shown, lalhat is the 30m 20m 3om 20m
Q1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 in, diam Water
Q2) Oil flows through a pipe as shown in fig2. The coefficient of discharge for the orifice in the pipe is C.-0,63. What is the discharge of oil in the pipe? P1-P2 P1-P2 V22-V₁² Let: -4.48. Y 100-mm-diameter, sharp-edged orifice (2) 250mm 6.958 Heavy oil
Water flows in a channel with uniform curvature R. The channel has height h = 6 mm and width w=190 mm (normal to the drawing plane) as shown in Fig Q3. The curved part of the channel has a length of 1 =95 mm in the x-direction. You can assume that the channel height is very small compared to the curvature radius. Neglect effects of gravity. channel y V X 1 lower wall h upper wall centreline Fig Q3: Geometry of curved channel, drawing not to scale. The curvature of the channel is not shown, as too small to be drawn accurately at this scale. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3.
This is a gentle reminder that you need to adhere to the time limit There are 80 minutes allotted for Section B, which starts running from the time you commence solving this question Within an urban development near the city of Bankstown, Sydney (Latitude:-33.917290 , Longitude: 151.035889) a roadway gutter transports water over a distance of 120m to pit A. The ARI adopted for the design is 50 years (or AFP = 1/T x 100 - 2%) Question B.1 Calculate the discharge from the catchment to pit A. Show the workings on the graph and tables you download from the BOM. Hint: For entry to pit A full area coefficient - part area coefficient. Consider the time of concentration from the remote pavement to the gutter (this includes the grassed verge and asphalt paving) - 2 minutes Provide IFD's or Rainfall intensity tables, which are used and show the working on all tables, and graphs used. Figure 2.docx Question B.2. Provide an estimate of the roof and gutter time for the residential lots Question…
Q1) Using a system similar to that shown in figure, compute the required air pressure above the water to cause the jet to rise h2 = 41 m from the nozzle. The depth h, -2.1 m. Air pressure