A vertical rod of length L and diameter dis fixed at its upper end and carries a load Wat its lower end. The extension of the rod due to load W is 6. When a torque Tis applied in a horizontal plane at the lower end of the rod, gives an angle of twist 0 radians. What is the correct expression of Poisson's ratio? Have any Doubt ?

A vertical rod of length L and diameter dis fixed at its upper end and carries a load Wat its lower end. The extension of the rod due to load W is 6. When a torque Tis applied in a horizontal plane at the lower end of the rod, gives an angle of twist 0 radians. What is the correct expression of Poisson's ratio? Have any Doubt ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.2P: A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to...

See similar textbooks

Similar questions

A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The steel axle of a large winch on an ocean liner is subjected to a torque of 1.65 kN · m (see figure). What is the minimum required diameter dminif the allowable shear stress is 48 M Pa and the allowable rate of twist is 0.75º/m? (Assume that the shear modulus of elasticity is 80 G Pa.) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d/8, Compare dminvalues to corresponding values from part (a)
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A magnesium-alloy wire of diameter d = 4mm and length L rotates inside a flexible tube in order to open or close a switch from a remote location (see figure). A torque Tis applied manually (either clockwise or counterclockwise) at end 5, thus twisting the wire inside the tube. At the other end A, the rotation of the wire operates a handle that opens or closes the switch. A torque T0 = 0.2 N · m is required to operate the switch. The torsional stiffness of the tube, combined with friction between the tube and the wire, induces a distributed torque of constant intensity t = 0.04N m/m (torque per unit distance) acting along the entire length of the wire. (a) If the allowable shear stress in the wire is T allow = 30 MPa, what is the longest permissible length Lmaxof the wire?
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A steel axle is made from tubes AB and CD and a solid section BC. It is supported on smooth bearings that allow it to rotate freely. If ends 4 and D are subjected to 85 Nm torques, determine the angle of twist of end B with respect to C. The tubes have an outer diameter of 30 mm and inner diameter of 20 mm. The solid section has a diameter of 40 mm. Steel has a shear modulus of elasticity G = 75 GPa. Provide your final answer in degrees.
B4 The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 Nm and an axial tensile force of 2 kN. Find: 500 Nm 500 Nm A 2kN 2kN (a) the tensile stress in the concrete;
The following rod has a diameter of 15 mm, and a length of 1000 mm, and was fixed at its one end to the wall. A force pair of 200 N is applied by a 500 mm length arm to the point A. Which material given below should be chosen for this rod material to keep the twist angle on the A plane less than 20°. Material Aluminium alloy Magnesium alloy Titanium alloy E, GPa 70 45 105 V 0,3 0,3 0,3 200 N 250 mm 250 mm 200 N
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.