A vertical rectangular water tank is divided into two chambers whose horizontal sections are 3 m² and 5 m², respectively. The dividing wall is provided with a 100mm by 100mm square hole located 0.5 m from the bottom and whose coefficient of discharge is 0.60. Initially there is 5 m deep of water in the smaller chamber and 1 m deep of water in the larger chamber. What is the difference in the water level in the two chambers after 2 minutes?

A vertical rectangular water tank is divided into two chambers whose horizontal sections are 3 m² and 5 m², respectively. The dividing wall is provided with a 100mm by 100mm square hole located 0.5 m from the bottom and whose coefficient of discharge is 0.60. Initially there is 5 m deep of water in the smaller chamber and 1 m deep of water in the larger chamber. What is the difference in the water level in the two chambers after 2 minutes?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular tank has an 34mm diameter orifice on one of its sides discharging oil with a specific gravity of 0.89. The tank has a 553mm diameter and has a depth of 2.7m. The orifice is located 0.20m above the bottom of the tank. The depth of oil inside the tank was initially 2.3m and 264s later, it became 0.7m. What is the coefficient of discharge?
A venturi meter of 150 × 75 mm size is fixed in a horizontal pipe carrying water. The pressure gauge at entry read 137.34 kN/m^2 (gauge). The pressure at the throat was 37.5 cm of mercury (vacuum). -Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr. choices: a.) 0.088 m^3/s b.) 0.345 m^3/s c.) 0.197 m^3/s d.) 0.441 m^3/s STRICTLY SHOW COMPLETE FBD need asap
A vertical circular tamk is 1.5 m high, has sloping sides. The tank is 50 m and 30 m in the top and bottom diameter respectively. Discharge takes place through a triangular orifice situated at the bottom of the tank. The orifice has a base of 0.8m long , o.5m below its vertex. If the tank is originally full of water , what time is required to empty the tank? Take discharge coefficient as 0.63
Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine the the required pumping power input for flow over a 200-feet long section of the pipe. A 530 Watts В 461 Watts C) 315 Watts D) None of the above
Please help me show work i leave thumbs up Thank you so much
Calculate the discharge from a tubewell of 20-cm diameter penetrating fully into a confined aquifer of 20-m thick and having a permeability of 40 m/day. The drawdown in the well is 3 m and zero drawdown at 300 m from the well. Q = 2.72 T (H-h) log 10 R/r Select one: O a. 1315.9 O b. 1303.7 O C. O d. 1257.3 1200.4
A steel pipe has an inside diameter of 25mm, is 20 meter long, carries 10degree water at the rate of 4.5 m3/h. if the static pressure at the inlet is 70 kPa, what is the static pressure of the water at the outlet. Make a graphical presentation.
A 5 cm diameter siphon tube is used to empty the pool and discharged it into air (figure below). Determine the discharge rate through the tube and pressure inside the house at point 1, 2, and 3. Assume no losses. Aut 3 2m 7m
Kindly show complete or detaled solution. A rectangular water tank is divided by a partition into two chambers, as shown. In the bottom of the partition is a round, sharp-edge orifice with a diameter of 150 mm. The coefficient of discharge is equals to 0.62. At a certain instant, the water level in B is 2.5 m higher than A. How long will it take for the water surfaces in the two chambers to be at the same level? a. 399 s b. 157 s c. 279 s d. 220 s
The diameter of a pipe gradually reduces from 1 m to 0.7 m. the pressure intensity at the centre line of 1 m section is 7.848 kN/m? and rate of flow of water though the pipe is 600 liters/s. The intensity of pressure (N/cm2) at the centre-line of 0.7 m section is (Correct up to 2 decimals)
29 REVIEW INNOVATIONS 2. A pipe 977 m long branches into 3 pipes at junction A. The three pipes span 1046 m, 885 m, and 796 m. They come together at junction B and continue as a single pipe for 1224 m. All pipes are 300 mm in size except the shortest one which is 250 mm. The pressure drop between the junctions is 260 kPa. Friction factor "f" can be assumed 0.02 in the entire system. Calculate the rates of flow in the branching pipes.
A prismatic vessel has two compartments A and B communicating by an orifice 0.3m square with C = 0.60. The horizontal cross – section of A is 10 sqm and that of B is 0.40 sqm. At a certain time, the water in A is 6m above the center of the orifice and in B is 3m. a. Compute the discharge from A to B. b. Find the time in which the water surfaces in the two tanks will reach the same elevation. c. How soon thereafter will the water surface be 1m apart? 3 m 6 m 3 m A B