A vertical rectangular gate 2m wide and 3 m high is submerged in water with its top edge flushed With the water surface. Find the following: 1. The value of the maximum force, F acting on center of pressure 2. The value of the eccentricity 3. The location of Force. F below the water surface 4. The magnitude of the maximum pressure

Q: Problem 4. The gate below is 1.5 m wide and hinged at point B. It rests against a smooth wall at…

A:

Q: Q2. A tainter gate of 90° sector is subjected to water pressure as shown in figure below. Determine…

A:

Q: A rectangular altitude of 2.4 m. The short side of the gate is flushed with the water surface.…

A:

Q: 1.0 A RECTANGULAR GATE 2.0 M X 5.0 M IS ACTED ON WATER ON ONE SIDE AND IS POSITIONED WITH ITS LONGER…

A:

Q: Each gate of a lock is 5m high and is supported by two hinges placed on the top and bottom of the…

A:

Q: A rectangular plate 0f 7 ft by 3.5 ft at an angle 450 with the horizontal, and the 7 ft side is…

A: Given data: a) Calculating at free water surface:

Q: 3. For the gate shown, α = 45°, y₁ = 1 m, and y₂ = 4 m. Will the gate fall or stay in position under…

A: Given :

Q: An isosceles triangular gate with long and vertex pointing downward The top of the gate is 4.5 m…

A:

Q: The sluice gate is a circular arc of radius 5m and angle B=60°. The water level behind the gate…

A: The radius of the circular arc, R= 5 mAngle, Length of the gate, L= 3 mTo find:The vertical…

Q: 3.0 A GATE 3M HIGH IS 2.5 M WIDE IS HINGED AT POINT B AND REST AGAINST A SMOOTH WALL AT A. POINT A…

A: Answer Let us first draw the free body diagram of forces acting on the gate (a) Calculation of…

Q: Water is flowing at 0.020 m'/s at steady-state through a reducing 90-degree bend in the horizontal…

A: given data Q=0.02m3/secd1=0.05m and…

Q: Water flows steadily through a pipe bend and exits through a nozzle at 2 into theatmosphere. Assume…

A: The objective of the question is to determine the vertical reaction, RY, at the clamp point R to…

Q: H.W.23/ The figure below shows a water-retaining gate with a curved portion. When the water level…

A:

Q: A crest gate shown in Figure 1. consists of a cylindrical surface of which AB is the base, supported…

A:

Q: Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downward such…

A:

Q: rectangular tank 4 m long. ater pressure on the base of the tank. Find also the depth of centre of…

A:

Q: Problem 4. The gate below is 1.5 m wide and hinged at point B. It rests against a smooth wall at…

A:

Q: A 1.5m semi cicular gate is submerged in oil having an SG of 0.95. its base is 2m from the surface…

A: Given data-  Diameter of semi cicular gate (d) = 1.5m Specific gravity  of oil(S.G) = 0.95 Density…

Q: A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25kN. Determine the…

A: Pressure at a point: The pressure at a point in fluids is defined by pascal's law. Pascal's law…

Q: Q.4.A..A (3m) high, (5m) wide rectangular gate is hinged at the top edge at (A), and is restrained…

A:

Q: Solve ALL FORCES and DRAW THE SHEAR FORCE (V-D) AND BENDING MOMENT (M-D) COMPLETELY of the following…

A: Support Reactions :  RA + RB = 2×12×4.5×5 = 22.5 kN ........(1)Taking moment about A,RB×9 -…

Q: A rectangular gate 1.2 m by 3 m is inclined 60° with the horizontal. The top of the gate is…

A:

Q: Wall AO is designed to block water which.1 rises to a level of 4 m. Determine the magnitude of force…

A: Force F should satisfy moment equilibrium, So take moment of F and hydrostatic force and make them…

Q: rectangular plan surface 5 m wide and 7 m deep lies in water in such a way that its plane makes an…

A:

Q: The length of submerged gate AB is 7 m. Determine the amount of horizontal and vertical components…

A:

Q: The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjected…

A:

Q: ANGULAR DOOR WASS REPLACED BY A 2 OF THE NEW DOOR. DETERMINE 45m 0 AND THE WATER SURFACE (KN), AND…

A:

Q: The length of submerged gate AB is 7 m. Determine the amount of horizontal and vertical components…

A: Solution; Given data; γw=9.81 KN/m2Length of the gate=7 m

Q: etermine the hydrostatic force of a circular gate of radius 3m which is submerged under water. a).…

A: Given:- Radius of circular gate = 3 m To find:- From the given question it is required to calculate…

Q: hydrostatic

A:

Q: Determine the horizontal component of the total hydrostatic force in Newton the water exerts on the…

A:

Q: Problem 4. The gate below is 1.5 m wide and hinged at point B. It rests against a smooth wall at…

A: Width of gate = 1.5 m Hinged at point B Specific gravity of sea water = 1.025 To find:- Force on…

Q: Question 2 (b) Using the same problem above. Compute the location in m of the hydrostatic force from…

A:

Q: Problem 2 Water flows through a horizontal 45 degree bend with a 22-i pressure of 15 lb/in². Pi L- y…

A: