**Analysis of an Unknown Two-Terminal Device****Illustration Description:**The image shows a diagram of an unknown two-terminal device with nodes labeled "a" and "b." The voltage between these nodes is denoted as \( v_{ab} \), with the positive sign at node "a" and negative sign at node "b."**Measurements:**Two key measurements are taken on this device:1. **Current Source Test:** - A 2 mA current source is connected between nodes "a" and "b." - Current flows positively into node "b." - The voltage measured is 48 mV, with the higher voltage at node "a."2. **Resistor Test:** - A 3 Ω resistor is connected between nodes "a" and "b." - The current is measured to be 5 mA, flowing from "a" to "b."**Problem Statement:**Determine the Thevenin equivalent voltage and resistance of the two-terminal device. - **Thevenin Equivalent Voltage (\( V_{th} \))**: [Input box]- **Thevenin Equivalent Resistance (\( R_{th} \))**: [Input box]

Given, The value of current in current source in part 1, I=2 mA=0.002 A The value of the resistor…

? + 。a Vab Fob Two measurements are made on an unknown two-terminal device: 1. When a 2mA current source is connected between nodes a and b with positive current flowing into node b, the voltage is measured to be 48mV with the higher voltage at node a. 2. When a 32 resistor is connected between nodes a and b, the current is measured to be 5mA with current flowing down (from a to b). What are the Thevenin equivalent voltage and resistance of the two-terminal device? Vth= Rth=

? + 。a Vab Fob Two measurements are made on an unknown two-terminal device: 1. When a 2mA current source is connected between nodes a and b with positive current flowing into node b, the voltage is measured to be 48mV with the higher voltage at node a. 2. When a 32 resistor is connected between nodes a and b, the current is measured to be 5mA with current flowing down (from a to b). What are the Thevenin equivalent voltage and resistance of the two-terminal device? Vth= Rth=

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

if the resistor R1 and R2 terminals are connected across each and R3 is connected along single terminal. If the R1=5 R2=10 and R3=15 ohms, what will be the Rtotal?
CIRCIUTS
please answer it completely
Two identical zinc-carbon batteries are available. When connected in series, they supply 0.5 ampere to a 4-ohm resistor. When connected in parallel, they supply 0.4 ampere to a 5-ohm resistor. Determine the emf and the internal resistance of each battery
B 12 V (+ 32 kn I, A 1 kM 2 kN 1 kN 2 mA D
In the circuit, Determine: a. the total resistance (R7) of the circuit in kl. (. . places for the final answer) b. the current flowing in mA for each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the 12V final answer) c. the voltage in V across each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the ; use 2 decimal R = 3000 R3 = 4000 R2 = 1000 R4 = 1ka %3! final answer)
A ammeter has a resistance of 0.1 ohm and full range is 100 A. To incraese range to 1000 A find value of shunt resistance. Please solve it.
In step 3, what is the potential difference across D2 after the jumper wire is connected
A battery of 60 cell is charged from a supply of 240V. Each cell has an e.m.f of 2 V at the start and 2.4 V at the end of charging. Each cell has 0.12 ohms internal resistance. A load of 20 ohms is connected in the circuit. Calculate a. Intial charging current b. Final charging current c. Additional resistance R to be added to circuit to give a 1.2 A current d. Final charging current if end voltage is 2.5 V per cell
Continuing with the same setup as above, where you connect a 6Q resistor and a 12 Q resistor in series to a 9 V battery. Find the potential difference, V1, across the 6 Q resistor in Volits Hint: VTOT = V1 = V2. RTot ITot BAT1 R2 12 Q R1 9 V
answer it theortical as it asked
Consider the circuit shown in the figure below, If the voltage at point a is 15V and point b is 6V, calculate the current of the 30 resistance. 32 a o 122 412 Oa 6A Ob. 7A Oc. 3A Od 9A